Influence of graphene coating in electrical discharge machining with an aluminum electrode-Reference-Cited by-同舟云学术

Influence of graphene coating in electrical discharge machining with an aluminum electrode

Published:2023-01-01 Issue:1 Volume:32 Page:
ISSN:2191-0243
Container-title:Journal of the Mechanical Behavior of Materials
language:en
Short-container-title:

Author:

Pham Van Dong¹,Shirguppikar Shailesh²,Huu Phan Nguyen¹,Thangaraj Muthuramalingam³,Le Thi Phuong Thanh¹,Trong Ly Nguyen¹,Ganachari Vaibhav²

Affiliation:

1. Faculty of Mechanical Engineering, Hanoi University of Industry , No. 298, Cau Dien Street, Bac TuLiem District , Hanoi , Vietnam

2. Department of Mechatronics Engineering, Rajarambapu Institute of Technology, Shivaji University , Sakharale, MS 414415 , India

3. Department of Mechatronics Engineering, SRM Institute of Science and Technology, Kattankulathur Campus , Tamilnadu, 603203 , India

Abstract

Abstract Since the cost of electrodes in electrical discharge machining (EDM) is usually too high, it leads to a significant increase in the production cost. Hence, it is important to conduct research aimed at reducing the manufacturing cost of electrodes. Currently, coated electrodes are a new process solution in EDM. It can improve the economic and technical efficiency of this technology. In this article, the efficiency of the graphene-coated aluminum (Al) electrode in the EDM for Ti–6Al–4V was analyzed and evaluated. Material removal rate and tool wear rate were used as quality indicators in this work. The research results have shown a significant improvement in quality characteristics in EDM with coated electrodes compared to EDM with uncoated electrodes. The surface quality of the specimen with coated electrodes in EDM was also improved.

Publisher

Walter de Gruyter GmbH

Subject

Mechanics of Materials,Materials Science (miscellaneous)

Link

https://www.degruyter.com/document/doi/10.1515/jmbm-2022-0287/pdf

Reference25 articles.

1. Nahak B, Gupta A. A review on optimization of machining performances and recent developments in electro discharge machining. Manuf Rev. 2019;6:2.

2. Nafi MA, Jahan MP. Functional Surface Generation by EDM – A review. Micromachines. 2023;14:115. 10.3390/mi14010115.

3. Ablyaz TR, Shlykov ES, Kremlev SS. Copper-coated electrodes for electrical discharge machining of 38X2H2MA steel. Russ Engin Res. 2017;37:910–1. 10.3103/S1068798X17100033.

4. Ablyaz T, Muratov K, Preetkanwal SB, Sarabjeet SS. Experimental investigation of wear resistance of copper coated electrode-tool during electrical discharge machining. IOP Conf Ser Mater Sci Eng. 2019;510:012001. 10.1088/1757-899X/510/1/012001.

5. Danade UA, Londhe SD, Metkar RM. Machining performance of 3D-printed ABS electrode coated with copper in EDM. Rapid Prototyp J. 2019;25:1224–31. 10.1108/RPJ-11-2018-0297.

Cited by 4 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Improving Micro-EDM Machining Efficiency for Titanium Alloy Fabrication with Advanced Coated Electrodes;Micromachines;2024-05-24

2. Investigating Technological Parameters and TiN-Coated Electrodes for Enhanced Efficiency in Ti-6Al-4V Micro-EDM Machining;Metals;2024-01-28

3. Optimizing micro-EDM with carbon-coated electrodes: A multi-criteria approach;International Journal of Modern Physics B;2024-01-11

4. Material Selection for PMEDM Process;International Journal of Mechanical Engineering and Robotics Research;2024