Investigation on the size effect in micro end milling considering the cutting edge radius and the workpiece material
-
Published:2021-05-17
Issue:1
Volume:12
Page:487-499
-
ISSN:2191-916X
-
Container-title:Mechanical Sciences
-
language:en
-
Short-container-title:Mech. Sci.
Author:
Li Yang,Cheng Xiang,Zheng Guangming,Liu Huanbao
Abstract
Abstract. Previous research has found that the peripheral and end cutting edges of the
cutter had different cutting mechanisms in the micro end cutting process
considering the size effect. This investigation is a further study on this
point considering the cutting edge radius of the cutter and the material of
the workpiece based on the methods of finite element simulation and the micro
end cutting experiment. This study adopts a combination of simulation
and experiment research methods and the cutting edge radius and the workpiece
material as two variables. Considering the cutting mechanisms of the
peripheral cutting edge and the end cutting edge are different, the
peripheral cutting edge and the end cutting edge are studied respectively.
Meanwhile, the minimum undeformed chip thickness (MUCT) value is determined in three ways, chip morphology,
cutting force, and surface roughness, so the final result obtained by
comparing three kinds of results has a very important reference value. Not
only are the chip morphology obtained by finite element simulation and the
surface roughness obtained by the micro end cutting experiment used to
identify the MUCT value, but also the
cutting force. The simulation and
experimental results show that the cutting force can be used to identify the
MUCT value for the peripheral cutting edge, but it cannot be used for the
end cutting edge. The MUCT value increases with the increase of the
cutting edge radius, no matter which process it is. The material property
has some effects on the MUCT value; even the cutting parameters and the
cutting edge radius remain unchanged for the peripheral cutting edge.
However, the material property has no effect on the MUCT value for the end
cutting edge. In this study, the influence of important variables on MUCT is
studied as much as possible to reflect a real application
situation.
Funder
National Key Research and Development Program of China Shandong University of Technology and Zibo City Integration Development Project
Publisher
Copernicus GmbH
Subject
Industrial and Manufacturing Engineering,Fluid Flow and Transfer Processes,Mechanical Engineering,Mechanics of Materials,Civil and Structural Engineering,Control and Systems Engineering
Reference19 articles.
1. Aramcharoen, A. and Mativenga, P. T.: Size effect and tool geometry in
micromilling of tool steel, Precis. Eng., 3, 402–407, 2009. 2. Cheng, X., Wei, X. T., and Yang, X. H.: Unified criterion for
brittle–ductile transition in mechanical microcutting of brittle materials,
J. Manuf. Sci. Eng., 136, 051013–051011, 2014. 3. Cheng, X., Liu, J. C., and Zheng, G. M.: Study of micro-cutting fundamentals
for peripheral and end cutting edges in micro-end-milling, J. Micromech.
Microeng., 28, 015011, https://doi.org/10.1088/1361-6439/aa9a73, 2018. 4. Cui, X. B., Yan, K., and Guo, J. X.: Bio-inspired fabrication, mechanical
characterization and cutting performance evaluation of Al2O3 / TiC
micro-nano-composite ceramic with varying microscopic surfaces, Ceram. Int.,
45, 8286–8299, 2019. 5. Cui, X. B., Guo, Y. H., and Guo, J. X.: Performance analysis of
laser-induced biomimetic ceramic tools in interrupted cutting, Int. J. Mech.
Sci., 177, 105589, https://doi.org/10.1016/j.ijmecsci.2020.105589, 2020a.
Cited by
8 articles.
订阅此论文施引文献
订阅此论文施引文献,注册后可以免费订阅5篇论文的施引文献,订阅后可以查看论文全部施引文献
|
|