Simulation of 316L Stainless Steel Produced the Laser Powder Bed Fusion Process-Reference-Cited by-同舟云学术

Simulation of 316L Stainless Steel Produced the Laser Powder Bed Fusion Process

Published:2023-12-15 Issue:24 Volume:16 Page:7653
ISSN:1996-1944
Container-title:Materials
language:en
Short-container-title:Materials

Author:

Kaščák Ľuboš¹^ORCID,Varga Ján¹^ORCID,Bidulská Jana²^ORCID,Bidulský Róbert³⁴^ORCID

Affiliation:

1. Department of Technology, Materials and Computer-Aided Production, Faculty of Mechanical Engineering, Technical University of Košice, Letná 9, 04002 Košice, Slovakia

2. Department of Plastic Deformation and Simulation Processes, Institute of Materials and Quality Engineering, Faculty of Materials, Metallurgy and Recycling, Technical University of Košice, Vysokoškolská 4, 04200 Košice, Slovakia

3. Bodva Industry and Innovation Cluster, Budulov 174, 04501 Moldava and Bodvou, Slovakia

4. Advanced Research and Innovation Hub, Budulov 174, 04501 Moldava and Bodvou, Slovakia

Abstract

Additive manufacturing is increasingly being used in the production of parts of simple as well as complex shapes designed for various areas of industry. Prevention of errors in the production process is currently enabled using simulation tools that have the function of predicting possible errors and, at the same time, providing a set of information about the behaviour of the material in the metal additive manufacturing process. This paper discusses the simulation processes of 316L stainless steel produced using the laser powder bed fusion (L-PBF) process. Simulation of the printing process in the Simufact Additive simulation program made it possible to predict possible deformations and errors that could occur in the process of producing test samples. After analysing the final distortion already with compensation, the simulation values of maximum deviation −0.01 mm and minimum −0.13 mm were achieved.

Funder

Ministry of Education, Science, Research, and Sport of the Slovak Republic

Publisher

MDPI AG

Subject

General Materials Science

Link

https://www.mdpi.com/1996-1944/16/24/7653/pdf

Reference67 articles.

1. Influence of particle size distribution and morphology on the properties of the powder feedstock as well as of AlSi10Mg parts produced by laser powder bed fusion (LPBF);Riener;Addit. Manuf.,2020

2. Processing parameters in laser powder bed fusion metal additive manufacturing;Oliveira;Mater. Des.,2020

3. Ninpetch, P., Kowitwarangkul, P., Chalermkarnnon, P., Promoppatum, P., Chuchuay, P., and Rattanadecho, P. (2022). Numerical Modeling of Distortion of Ti-6Al-4V Components Manufactured Using Laser Powder Bed Fusion. Metals, 12.

4. Lu, X., Chiumenti, M., Cervera, M., Tan, H., Lin, X., and Wang, S. (2021). Warpage Analysis and Control of Thin-Walled Structures Manufactured by Laser Powder Bed Fusion. Metals, 11.

5. The Efficacy of The Inherent Strain Method in Determining Residual Stress in In718 SLM Specimens;Botha;S. Afr. J. Ind. Eng.,2021

Cited by 4 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Influence of Phase Transformation Coefficient on Thermomechanical Modeling of Laser Powder Bed Fusion for Maraging 300 Steel;Journal of Materials Research and Technology;2024-09

2. Formability Assessment of Additively Manufactured Materials via Dieless Nakajima Testing;Journal of Manufacturing and Materials Processing;2024-08-18

3. Weight Factor as a Parameter for Optimal Part Orientation in the L-PBF Printing Process Using Numerical Simulation;Materials;2024-07-22

4. Weldability of Additively Manufactured Powder Bed Fusion 316L Stainless Steel Using Arc and Laser Welding;Crystals;2024-03-25