An Experimental Study of Molten Microdroplet Surface Deposition and Solidification: Transient Behavior and Wetting Angle Dynamics
Author:
Attinger D.1, Zhao Z.1, Poulikakos D.1
Affiliation:
1. Laboratory of Thermodynamics in Emerging Technologies, Institute of Energy Technology, Swiss Federal Institute of Technology (ETH), 8092 Zurich, Switzerland
Abstract
The basic problem of the impact and solidification of molten droplets on a substrate is of central importance to a host of processes. An important and novel such process in the area of micromanufacturing is solder jetting where microscopic solder droplets are dispensed for the attachment of microelectronic components. Despite the recent appearance of a few numerical studies focusing on the complex transient aspects of this process, no analogous experimental results have been reported to date to the best of our knowledge. Such a study is reported in this paper. Eutectic solder (63Sn37Pb) was melted to a preset superheat and used in a specially designed droplet generator to produce droplets with diameters in the range 50–100 μm. In a first series of experiments, the size, temperature, and impacting speed of the molten droplets were maintained constant. The primary variable was the temperature of the substrate that was controlled in the range from 48°C to 135°C. The dynamics of molten solder microdroplet impact and solidification on the substrate was investigated using a flash microscopy technique. The time for the completion of solidification from the moment of a solder droplet impact on the substrate varies between 150 μs and 350 μs. The dynamic interaction between the oscillation in the liquid region and the rapid advance of the solidification front was visualized, quantified, and presented in this paper. In a second series of experiments, the evolution of the wetting angle between the spreading drop and the substrate was recorded and analyzed. No quantitative agreement with Hoffman’s correlation for wetting was found. It was established that the wetting angle dynamics is strongly coupled with the evolution of the droplet free surface. Two successive regimes were distinguished during the spreading. The influence of the initial impact velocity and substrate temperature on the dynamics of the measured wetting angle was described in both regimes. To the best of our knowledge, this study presents the first published experimental results on the transient fluid dynamics and solidification of molten microdroplets impacting on a substrate at the above-mentioned time and length scales that are directly relevant to the novel solder jetting technology. [S0022-1481(00)01403-1]
Publisher
ASME International
Subject
Mechanical Engineering,Mechanics of Materials,Condensed Matter Physics,General Materials Science
Reference42 articles.
1. Orme, M.
, 1993, “A Novel Technique of Rapid Solidification Net-Form Materials Synthesis,” J. Mater. Eng. Perform., 2, No. 3, pp. 399–405. 2. Orme, M., Huang, C., and Courter, J., 1996, “Deposition Strategies for Control of Microstructures Microporosity and Surface Roughness in Droplet-Based Solid Freeform Fabrication of Structural Materials,” Melt Spinning, Strip Casting and Slab Casting, Matthys, E. F., and Truckner, W. G., eds., The Minerals, Metals and Materials Society, Warrendale, PA, pp. 125–143. 3. Hayes, D. J., and Wallace, D. B., 1998, “Solder Jet Printing: Wafer Bumping and CSP Applications,” Chip Scale Rev., 2, No. 4, pp. 75–80. 4. Waldvogel, J. M., Diversiev, G., Poulikakos, D., Megaridis, C. M., Attinger, D., Xiong, B., and Wallace, D. B., 1998, “Impact and Solidification of Molten-Metal Droplets on Electronic Substrates,” ASME J. Heat Transfer, 120, p. 539539. 5. Haferl, S., Zhao, Z., Giannakouros, J., Attinger, D., and Poulikakos, D., 2000, “Transport Phenomena in the Impact of a Molten Droplet on a Surface: Macroscopic Phenomenology and Microscopic Considerations, Part I: Fluid Dynamics,” Annu. Rev. Heat Transfer, C. L. Tien, ed.
Cited by
150 articles.
订阅此论文施引文献
订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献
|
|