Mechanism of Nucleate Boiling Heat Transfer Enhancement From Microporous Surfaces in Saturated FC-72-Reference-Cited by-同舟云学术

Mechanism of Nucleate Boiling Heat Transfer Enhancement From Microporous Surfaces in Saturated FC-72

Published:2002-05-10 Issue:3 Volume:124 Page:500-506
ISSN:0022-1481
Container-title:Journal of Heat Transfer
language:en
Short-container-title:

Author:

Kim J. H.¹,Rainey K. N.²,You S. M.¹,Pak J. Y.³

Affiliation:

1. The University of Texas at Arlington, Department of Mechanical and Aerospace Engineering, P.O. Box 19023, Arlington, TX 76019-0023

2. Los Alamos National Laboratory, P.O. Box 1663, MS-B258, Los Alamos, NM 87545-1663

3. Behr America Inc., 2700 Daley Dr., Troy, MI 48033

Abstract

The present study is an experimental investigation of the nucleate pool boiling heat transfer enhancement mechanism of microporous surfaces immersed in saturated FC-72. Measurements of bubble size, frequency, and vapor flow rate from a plain and microporous coated 390 μm diameter platinum wire using the consecutive-photo method were taken to determine the effects of the coating on the convective and latent heat transfer mechanisms. Results of the study showed that the microporous coating augments nucleate boiling performance through increased latent heat transfer in the low heat flux region and through increased convection heat transfer in the high heat flux region. The critical heat flux for the microporous coated surface is significantly enhanced over the plain surface due to decreased latent heat transfer (decreased vapor generation rate) and/or increased hydrodynamic stability from increased vapor inertia; both of which are a direct result of increased nucleation site density.

Publisher

ASME International

Subject

Mechanical Engineering,Mechanics of Materials,Condensed Matter Physics,General Materials Science

Link

http://asmedigitalcollection.asme.org/heattransfer/article-pdf/124/3/500/5912495/500_1.pdf

Reference28 articles.

1. Kurihara, H. M., and Myers, J. E., 1960, “The Effects of Superheat and Surface Roughness on Boiling Coefficients,” AIChE J., 6(1), pp. 83–91.

2. Berenson, P. J. , 1962, “Experiments on Pool-Boiling Heat Transfer,” Int. J. Heat Mass Transf., 5, pp. 985–999.

3. Nishio, S., and Chandratilleke, G. R., 1989, “Steady-State Pool Boiling Heat Transfer to Saturated Liquid Helium at Atmospheric Pressure,” JSME Int. J., Ser. II, 32(4), pp. 639–645.

4. Ramilison, J. M., Sadasivan, P., and Lienhard, J. H., 1992, “Surface Factors Influencing Burnout on Flat Heaters,” ASME J. Heat Transfer, 114(1), pp. 287–290.

5. Griffith, P., and Wallis, J. D., 1960, “The Role of Surface Conditions in Nucleate Boiling,” Chemical Engineering Progress Symposium Series No. 49, 56, pp. 49–63.

Cited by 79 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Flow boiling heat transfer enhancement of R134a in additively manufactured minichannels with microengineered surfaces;Applied Thermal Engineering;2024-11

2. An Overview of Innovative Surface-Modification Routes for Pool Boiling Enhancement;Micromachines;2024-02-22

3. Enhanced liquid replenishment for pool boiling heat transfer and its CHF mechanism on patterned freeze-casted surfaces;Experimental Thermal and Fluid Science;2024-01

4. Investigation of effect of a mechanical agitator on pool boiling heat transfer;International Communications in Heat and Mass Transfer;2022-12

5. Effect of R-600a and distilled water on nucleate pool boiling characteristics from horizontal tubes at low and moderate heat flux;Heat and Mass Transfer;2022-06-10