Nonproportional Low Cycle Fatigue Criterion for Type 304 Stainless Steel-Reference-Cited by-同舟云学术

Nonproportional Low Cycle Fatigue Criterion for Type 304 Stainless Steel

Published:1995-07-01 Issue:3 Volume:117 Page:285-292
ISSN:0094-4289
Container-title:Journal of Engineering Materials and Technology
language:en
Short-container-title:

Author:

Itoh Takamoto¹,Sakane Masao²,Ohnami Masateru²,Socie Darrell F.³

Affiliation:

1. Department of Mechanical Engineering, Faculty of Engineering, Fukui University, 9-1 Bunkyo 3-chome Fukui, 910, Japan

2. Department of Mechanical Engineering, Faculty of Science and Engineering, Ritsumeikan University, 1916 Noji-cho Kusatsu-shi Shiga, 525-77, Japan

3. Department of Mechanical and Industrial Engineering, University of Illinois, 140 Mechanical Engineering, 1206 West Green Street, Urbana, IL 61801

Abstract

This paper describes a multiaxial low cycle fatigue parameter for correlating Hues under nonproportional loadings. Constant amplitude low cycle fatigue tests were carried out under 14 proportional and complex nonproportional cyclic strain paths using type 304 stainless steel hollow cylinder specimens at room temperature. In nonproportional loading tests, fatigue lives are decreased by as much as a factor of 10 in comparison with those in proportional loading tests with the same strain range. Reduction in fatigue life due to nonproportional loading is closely related to additional nonproportional cyclic hardening. The product of the maximum principal stress and strain ranges correlated the nonproportional fatigue data. A nonproportional cyclic hardening parameter computed from the strain path is also proposed that allows life estimates to be obtained directly from the strain history without the need for a cyclic plasticity model.

Publisher

ASME International

Subject

Mechanical Engineering,Mechanics of Materials,Condensed Matter Physics,General Materials Science

Link

http://asmedigitalcollection.asme.org/materialstechnology/article-pdf/117/3/285/5525427/285_1.pdf

Reference25 articles.

1. ASME Code Case N-47, 1978, Case of ASME Boiler and Pressure Vessel Code, Case N-47, Class 1, Section 3, Division 1, ASME.

2. Benallal A. , and MarquisD., 1987, “Constitutive Equations for Nonproportional Cyclic Elasto-Viscoplasticity,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 109, No. 4, pp. 326–336.

3. Doong S. H. , SocieD. F., and RobertsonI. M., 1990, “Dislocation jubstructures and Nonproportional Hardening,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 112, No. 4, pp. 456–465.

4. Doong S. H. , and SocieD. F., 1991, “Constitutive Modeling of Metals Under Nonproportional Loading,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 113, No. 1, pp. 23–30.

5. Fatemi A. , and SocieD. F., 1988, “A Critical Plane Approach to Multiaxial Fatigue Damage Including Out-of-Phase Loading,” Fatigue and Fracture of Engineering Materials and Structures, Vol. 11, No. 3, pp. 149–165.

Cited by 196 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. A semi-empirical life-prediction model for multiaxial ratchetting-fatigue interaction of SUS301L stainless steel tubular welded joint;International Journal of Fatigue;2024-11

2. Predicting fatigue life with the IMWCW under complex loading;International Journal of Mechanical Sciences;2024-11

3. On how S-N curves for nonproportional loading can be determined from S-N curves for proportional loading – An exemplary evaluation of numerous fatigue tests using scaled normal stresses;International Journal of Fatigue;2024-11

4. Comparation of non-proportional hardening behavior and microscopic mechanism for CP-Ti under strain-controlled and stress-controlled multiaxial low cycle fatigue;Journal of Alloys and Compounds;2024-10

5. An engineering applicable method for multiaxial fatigue under proportional and non-proportional loads based on the octahedral plane projection;International Journal of Fatigue;2024-10