Experimental and Numerical Investigation of the Flow in a Centrifugal Compressor Volute-Reference-Cited by-同舟云学术

Experimental and Numerical Investigation of the Flow in a Centrifugal Compressor Volute

Published:1999-02-01 Issue:1 Volume:122 Page:22-31
ISSN:0889-504X
Container-title:Journal of Turbomachinery
language:en
Short-container-title:

Author:

Hagelstein D.¹,Hillewaert K.²,Van den Braembussche R. A.²,Engeda A.³,Keiper R.⁴,Rautenberg M.¹

Affiliation:

1. Institute of Turbomachinery, University of Hannover, Hannover, Germany

2. Von Karman Institute for Fluid Dynamics (VKI), Rhode Saint Gene`se, Belgium

3. Michigan State University, East Lansing, MI 48109

4. Ku¨hnle, Kopp & Kausch AG (KKK), Frankenthal, Germany

Abstract

This paper presents the experimental and numerical investigation of an outward volute of rectangular cross section. The investigation is carried out at the level of stage performance, volute performance, and detailed flow field study at selected peripheral positions for various operating points. The objective of the investigation was to gain further knowledge about the flow structure and loss mechanism in the volute. Simultaneously with the experimental investigation, a numerical simulation of the flow in the volute was carried out. A three-dimensional Euler code was used in which a wall friction term and a tuned artificial dissipation term account for viscous effects. A reasonable agreement between the experimental and numerical results is observed. As a result a good and detailed knowledge about the pressure recovery and loss mechanism in the volute is obtained. [S0889-504X(00)00301-9]

Publisher

ASME International

Subject

Mechanical Engineering

Link

http://asmedigitalcollection.asme.org/turbomachinery/article-pdf/122/1/22/5841087/22_1.pdf

Reference22 articles.

1. Hagelstein, D., Van den Braembussche, R. A., Keiper, R., and Rautenberg, M., 1997, “Experimental Investigation of the Circumferential Static Pressure Distortion in Centrifugal Compressor Stages,” ASME Paper No. 97-GT-50.

2. Sorokes, J. M., Borer, C. J., and Koch, J. M., 1998, “Investigation of the Circumferential Static-Pressure Non-uniformity Caused by a Centrifugal Compressor Discharge Volute,” ASME Paper No. 98-GT-326.

3. Borer, C., Sorokes, J., McMahon, T., and Abraham, E., 1997, “An Assessment of the Forces Acting Upon a Centrifugal Impeller Using Full Load, Full Pressure Hydrocarbon Testing,” Proc. Texas A & M Turbomachinery Symposium.

4. Iversen, H. W., Rolling, R. E., and Carlson, J. J., 1960, “Volute Pressure Distribution, Radial Force on the Impeller, and Volute Mixing Losses of a Radial Flow Centrifugal Pump,” ASME J. Eng. Power, 82, No. 1, pp. 136–144.

5. Kurokava, J., 1980, “Theoretical Determination of the Flow Characteristics in Volutes,” Proc. IAHR-AIRH Symposium 1980, Tokyo, Japan.

Cited by 39 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Differences in Formation Mechanism of Static Pressure Circumferential Distribution of Centrifugal Compressor Under Different Operating Conditions;Journal of Fluids Engineering;2021-10-06

2. Effect of housing size on the performance of a centrifugal compressor for turbocharger application: An experimental and numerical study;Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering;2021-10-05

3. Effect of housing surface roughness on the performance of a centrifugal compressor for turbocharger: Experimental and numerical study;International Journal of Engine Research;2021-09-29

4. Assessment of the Loss Map of a Centrifugal Compressor's External Volute;Journal of Turbomachinery;2021-07-27

5. Influence of vaned diffuser on the potential effect of volute and stall inception of centrifugal compressor;Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering;2020-05-13