Numerical Simulation of Physical-Mechanical Properties Based on the Composition of GTAW Weld Metal Alloys with Dissimilar Base Metals
-
Published:2021-07-13
Issue:
Volume:892
Page:150-158
-
ISSN:1662-9795
-
Container-title:Key Engineering Materials
-
language:
-
Short-container-title:KEM
Author:
Sugianto 1, Riswanda 1, Harlian Kadir1, Akhyar Akhyar2, Aminur 3, Arman Faslih3
Affiliation:
1. Politeknik Negeri Bandung 2. Syiah Kuala University 3. Universitas Halu Oleo
Abstract
Dissimilar weld-metal joints in aluminum alloys 5083 and 6061-T6 are often found in aircraft, railroad structures, ships, bridges, oil platforms, and building structures. However, welding of dissimilar metals is relatively more difficult due to the different metallurgy and thermophysical properties of the two alloys. The purpose of this study is to evaluate the physical-mechanical properties of the Tungsten Arc Welding (GTAW) process through numerical simulations of different welded joints between the 5083 and 6061-T6 aluminum alloys. The GTAW welding simulation process is carried out by 300 x 100 x 3 mm plate butt joints along 300 mm. GTAW weld metal is prepared for tensile test samples and metal alloy composition, the test is observed in the base metal and welded area. The results of the chemical composition test of the weld metal obtained that the composition is close to Al 5083 base metal so that the mechanical properties of the weld metal tend to be identical with Al 5083 alloy. The results of numerical simulation on the mechanical properties of GTAW weld metal at temperature conditions of 25 to 700 °C obtained several things, including 1) the range of thermal conductivity decreased from 174.393 to 86.424 W/mK. 2) The density increased from 2,348 to 2,663 gr/cm3. 3), the young modulus appears to decrease from 68,667 to 0 GPa. 4) the shear modulus decreases from 25,724 to 0 GPa. 5) the type of heat increases from 0.904 to 17,306 J/gK, and 6) the Poisson ratio increased from 0.335 to 0.5.
Publisher
Trans Tech Publications, Ltd.
Subject
Mechanical Engineering,Mechanics of Materials,General Materials Science
Reference14 articles.
1. Akhyar, Husaini, H., Iskandar, F., Ahmad, Structural Simulations of Bicycle Frame Behaviour under Various Load Conditions, Materials Science Forum, 961, (2019), 137-147, https://doi.org/10.4028/www.scientific.net/MSF.961.137. 2. Akhyar, Husaini, M. Ali, N. Ali, F. Ahmad, Effect of Different Gating Systems and Sand Mold Binder on the Cast-Quality of Bicycle Frame Produced through Sand Casting Method, Defect and Diffusion Forum, 402, (2020), 100-107, https://doi.org/10.4028/www.scientific.net/DDF.402.100. 3. V. Malau, Akhyar, P.T. Iswanto, Modification of constrained rod casting mold for new hot tearing measurement, Archives of Metallurgy and Materials, 63(3), (2018), 1201-1208,. 4. H. Akhyar, P.T. Iswanto, V. Malau, Non Treatment, T4 and T6 on Tensile Strength of Al-5.9Cu-1.9Mg Alloy Investigated by Variation of Casting Temperature, Materials Science Forum, 929, (2018), 56-62, https://doi.org/10.4028/www.scientific.net/MSF.929.56. 5. M. Rathod, and T. Karale, Friction Stir Welding of Aluminium-Alloys, SAE Technical Paper, 28, (2014),.
Cited by
1 articles.
订阅此论文施引文献
订阅此论文施引文献,注册后可以免费订阅5篇论文的施引文献,订阅后可以查看论文全部施引文献
|
|