Influence of Superimposing of Oscillation on Sheet-Bulk Metal Forming-Reference-Cited by-同舟云学术

Influence of Superimposing of Oscillation on Sheet-Bulk Metal Forming

Published:2013-06 Issue: Volume:554-557 Page:1484-1489
ISSN:1662-9795
Container-title:Key Engineering Materials
language:
Short-container-title:KEM

Author:

Behrens Bernd Arno¹,Hübner Sven¹,Vucetic Milan¹

Affiliation:

1. Leibniz Universität Hannover

Abstract

Due to novel processes like sheet-bulk metal forming, the requirements for sheet metal forming are increased. Sheet-bulk metal forming is a new interconnected process in which the part itself is manufactured by deep drawing and the gearing will be produced with bulk forming in a combined process at room temperature. This process is characterized by a triaxial state of stress and a triaxial dimensional change with true strains up to  = 1-2 by using sheet blanks. Within the use of superimposing of oscillation on a sheet-bulk metal forming process the required forming force can be reduced and the accuracy of dimension of the part can be improved. Within this paper the influence of the superimposing of oscillation on the sheet bulk metal forming will be shown on combined ironing and external extrusion process. For the superimposing of oscillation different excitation frequencies will be analysed. Furthermore the die clearance will be varied to increase the requirements on the process. Finally the influence of the different excitation frequencies and the different die clearances will be summarized in cause and effect relationship diagram.

Publisher

Trans Tech Publications, Ltd.

Subject

Mechanical Engineering,Mechanics of Materials,General Materials Science

Link

https://www.scientific.net/KEM.554-557.1484.pdf

Reference9 articles.

1. M. Merklein, J.M. Allwood, B. -A. Behrens, A. Brosius, H. Hagenah, K. Kuzman, K. Mori, A. E. Tekkaya, A. Weckenmann, , 2012, Bulk forming of sheet metal, CIRP Annals - Manufacturing Technology, 59/2, http: /dx. doi. org/10. 1016/j. bbr. 2011. 03. 031.

2. M. Werbs, A. Bawohl, L. Gerlach: Kostengünstige Herstellung verzahnter Bauteile durch Blechmassivumformung, Tagungsband zum 1. Erlanger Workshop Blechmassivumformung, Bamberg: Meisenbach, 2011, pp.2-14.

3. A. Weckenmann, B. -A. Behrens, E. Reithmeier, G. Akkasoglu, M. Vucetic, T. Cahyono, C. Ohrt, S. Hübner, M. Kästner, Appliance of the matury method in the development of endoscopic geometry inspection for sheet bulk metal forming tools, in: Total Quality Management & Excellence 39 (2011).

4. M. Merklein, Manufacturing of complex functional components with variants by using a new sheet-metal forming process, Proceedings of the 42th International Cold Forging Group ICFG, Shnaghai, 2009, pp.143-155.

5. B. -A. Behrens, S. Hübner, M. Vucetic, Shortening the process chain by sheet-bulk metal forming processes, Proceedings of the 10th Global Conference on Sustainable Manufacturing, Istanbul 2012, pp.64-68.

Cited by 19 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Sheet Bulk Forming of Thin-Walled Components with External Gearing through Upsetting Using Controllable Deformation Zone Method;Chinese Journal of Mechanical Engineering;2021-12

2. Modeling, analysis, and multi-objective optimization of cold extrusion process of clutch outer gear hub using response surface method and meta-heuristic approaches;The International Journal of Advanced Manufacturing Technology;2021-06-15

3. Numerical simulation and experimental study on cold extrusion process for clutch outer gear hub with inner tooth shapes;The International Journal of Advanced Manufacturing Technology;2021-01

4. Dynamic Process Forces;Lecture Notes in Production Engineering;2020-11-05

5. Investigation of a Superimposed Oscillation Compression Process for the Production of a Bulk Component;Lecture Notes in Production Engineering;2020-09-25