Affiliation:
1. Lukasiewicz Research Network – Institute for Ferrous Metallurgy
2. Silesian University of Technology
3. ZM “WSK Rzeszów” Sp. z o.o.
Abstract
Cast magnesium alloys are characterised by the lowest density
among commercially used structural metals. They are applied
mainly in the transportation industry and small, lightweight electronic
devices. Due to the low operating temperature of the most
widely used alloys from the Mg-Al system, alloys containing rare
earth elements with the maximum working temperature reaching
300°C have been developed. However, these alloys are extremely expensive
due to the low availability of RE elements. The Mg-Bi system
is a promising candidate for the new magnesium-based alloys,
as it reveals limited solubility of Bi in Mg enabling precipitation
hardening and a high melting point of the Mg3Bi2 phase. The paper
presents the results of the analysis of MgBi6 and MgBi6X0.5
(X = Ca, Mn, Zn) alloys’ microstructure in the peak-aged condition.
The microstructure of the analysed alloys in the as-cast condition
consists of α-Mg solid solution dendrites and Mg3Bi2+α-Mg eutectic
compound. Solutionising conducted at 525°C for 8 h, followed by
water quenching leads to the dissolution of the intermetallic phases
in all of the investigated alloys apart of the MgBi6Ca0.5 alloy. In
this case, fine intermetallic phases containing Mg, Bi, and Ca have
been found after solutionising. The ageing of the alloys at 200°C
results in peak hardness after 120–144 h. The heat treatment leads
to the formation of fine strengthening phases within the α-Mg solid
solution, characterised by a variety of morphologies – needle,
platelet- or lathlike and cuboid. The needle- and platelet- or lathlike
phases are found in two sizes – large, with length reaching hundreds
of nanometres, and smaller, not exceeding 100 nm. Cuboid
particles are found with sizes not higher than 100 nm. The addition
of Mn and Zn increases precipitate volume fraction after the heat
treatment. Additionally, in the case of the MgBi6Zn0.5 alloy, particles
forming an angle of 120° were found, which indicates their
presence at the prismatic planes of α-Mg HCP crystal lattice.
Publisher
Siec Badawcza Lukasiewicz - Instytut Metalurgii Zelaza im. St. Staszica
Reference15 articles.
1. T. Rzychoń, A. Kiełbus, J. Szala. Microstructure and fluidity of sand cast ZRE1 alloy. J. Achiev. Mater. Manuf. Eng., 2008, 26 (2), pp. 135–138.
2. X.Y. Wang, J.X. Zhou, J. Wang, T.J. Luo, Y.S. Yang. Effect of Bi addition on microstructures and mechanical properties of AZ80 magnesium alloy. T. Nonferr. Metal. Soc., 2011, 21 (4), pp. 711–716.
3. W. Zhou, N.N. Aung, Y. Sun. Effect of antimony, bismuth and calcium addition on corrosion and electrochemical behaviour of AZ91 magnesium alloy. Corros. Sci., 2009, 51 (2), pp. 403–408.
4. D.H. Ping, K. Hono, J.F. Nie. Atom probe characterization of plate-like precipitates in a Mg-RE-Zn-Zr casting alloy. Scripta Mater., 2003, 48 (8), pp. 1017–1022.
5. J.F. Nie, B.C. Muddle. Characterisation of strengthening precipitate phases in a Mg-Y-Nd alloy. Acta Mater., 2000, 48 (8), pp. 1691–1703.