Experimental Investigation on the Coating of Nickel-Base Super Alloy Using Wire Flame Spraying-Reference-Cited by-同舟云学术

Experimental Investigation on the Coating of Nickel-Base Super Alloy Using Wire Flame Spraying

Published:2022-12-01 Issue:1 Volume:14 Page:28-39
ISSN:2066-8910
Container-title:Acta Universitatis Sapientiae, Electrical and Mechanical Engineering
language:en
Short-container-title:

Author:

Menasri Noureddine¹^ORCID,Zergane Said¹^ORCID,Aimeur Noureddine¹^ORCID,Saci Abdelhamid²

Affiliation:

1. University Mohamed Boudiaf of M’sila , Algeria

2. Maintenance Equipments Industrial (M.E.I) M’sila, plasma service , Algeria

Abstract

Abstract Inconel738 is a nickel-based super alloy widely used in manufacturing gas turbines, particularly in the manufacture of blades that are in direct contact with hot gases during their operation. As a result, these blades are subjected to high temperatures, significant static and dynamic stresses, erosion and/or hot corrosion which can be very severe. The use of coatings is one of the most effective strategies to protect materials against corrosion and increase the wear resistance of materials. In this study, β-Ni-Al coatings were sprayed onto an Inconel738 substrate using a wire flame spraying process and characterization of coating has been made.

Publisher

Walter de Gruyter GmbH

Subject

Polymers and Plastics,General Environmental Science

Link

https://www.sciendo.com/pdf/10.2478/auseme-2022-0003

Reference37 articles.

1. [1] Mudgal, D., et al., “Corrosion behavior of bare, Cr3C2-25%(NiCr), and Cr3C2-25%(NiCr)+ 0.4% CeO2-coated superni 600 under molten salt at 900° C”, Journal of materials engineering and performance, Vol. 23, no. 11, pp. 3805–3818, 2014. DOI: https://doi.org/10.1007/s11665-014-1177-3.10.1007/s11665-014-1177-3

2. [2] Kumar, S., et al., “Cyclic oxidation behavior of bare and Cr3C2-25 (NiCr) coated super alloy at elevated temperature”, Adv. Mater. Lett, Vol. 4, no. 10, pp. 754–761, 2013. DOI: https://doi.org/10.5185/amlett.2013.2428.10.5185/amlett.2013.2428

3. [3] Yang, Q., Xing, A., and Zhanqiang, L., “Machining performance and tool wear of coated carbide inserts in high speed turning powder metallurgy nickel-base superalloy”, in 2010 WASE International Conference on Information Engineering, IEEE, 2010, pp. 71–74.10.1109/ICIE.2010.195

4. [4] Mazur, Z., et al., “Failure analysis of a gas turbine blade made of Inconel 738LC alloy”, Engineering failure analysis, Vol. 12, no. 3, pp. 474–486, 2005. DOI: https://doi.org/10.1016/j.engfailanal.2004.10.002.10.1016/j.engfailanal.2004.10.002

5. [5] Li, S.-L., Qi, H.-Y., and Yang, X.-G., “Oxidation-induced damage of an uncoated and coated nickel-based superalloy under simulated gas environment”, Rare Metals, Vol. 37, no. 3, pp. 204–209, 2018. DOI: https://doi.org/10.1007/s12598-017-0931-8.10.1007/s12598-017-0931-8