METHODS OF FORMULATING AND SOLVING OPTIMIZATION PROBLEMS OF CUTTING LOGS OF LARGE SIZE BY BAR-SAWING METHOD WITH CUTTING OUT ONE BAR AND FIVE PAIRS OF SIDE EDGING BOARDS WITH SUBSEQUENT SAWING LUMBER FOR EDGED BOARDS-Reference-Cited by-同舟云学术

METHODS OF FORMULATING AND SOLVING OPTIMIZATION PROBLEMS OF CUTTING LOGS OF LARGE SIZE BY BAR-SAWING METHOD WITH CUTTING OUT ONE BAR AND FIVE PAIRS OF SIDE EDGING BOARDS WITH SUBSEQUENT SAWING LUMBER FOR EDGED BOARDS

Published:2017-08-15 Issue:1 Volume:7 Page:137-150
ISSN:2222-7962
Container-title:Forestry Engineering Journal
language:en
Short-container-title:

Author:

Агапов ,Agapov Aleksandr

Abstract

For the first time the mathematical model of task optimization for this scheme of cutting logs, including the objective function and six equations of connection. The article discusses Pythagorean area of the logs. Therefore, the target function is represented as the sum of the cross-sectional areas of edging boards. Equation of the relationship represents the relationship of the diameter of the logs in the vertex end with the size of the resulting edging boards. This relationship is described through the use of the Pythagorean Theorem. Such a representation of the mathematical model of optimization task is considered a classic one. However, the solution of this mathematical model by the classic method is proved to be problematic. For the solution of the mathematical model we used the method of Lagrange multipliers. Solution algorithm to determine the optimal dimensions of the beams and side edging boards taking into account the width of cut is suggested. Using a numerical method, optimal dimensions of the beams and planks are determined, in which the objective function takes the maximum value. It turned out that with the increase of the width of the cut, thickness of the beam increases and the dimensions of the side edging boards reduce. Dimensions of the extreme side planks to increase the width of cut is reduced to a greater extent than the side boards, which are located closer to the center of the log. The algorithm for solving the optimization problem is recommended to use for calculation and preparation of sawing schedule in the design and operation of sawmill lines for timber production. When using the proposed algorithm for solving the optimization problem the output of lumber can be increased to 3-5 %.

Publisher

Voronezh State University of Forestry and Technologies named after G.F. Morozov

Reference19 articles.

1. Агапов, А. И. Оптимизация раскроя пиловочника средних размеров при брусово-развальном способе распиловки [Текст] / А. И. Агапов // Современная наука : актуальные проблемы и пути их решения : 7-я междунар. дистанционная науч. конф., Липецк, 20-21 февраля 2014 г. – Липецк : МАКСИМАЛ, 2014. – С. 16-24., Agapov A. I. Optimizaciya raskroya pilovochnika srednih razmerov pri brusovo_razvalnom sposobe raspilovki [Optimization of cutting logs with a medium-sized lumber-cutting method breakup] Sovremennaya nauka _ aktualnie problemi i puti ih resheniya: 7-ya mejdunar. distancionnaya nauch. konf. [Modern science : actual problems and ways of their solution : 7-I-Nar. remote scientific. Conf.]. Lipeck, 2014, pp. 16 (In Russian).

2. Агапов, А. И. Оптимизация раскроя пиловочника с выпиливанием трех брусьев разной толщины и двух пар боковых досок [Текст] / А. И. Агапов // Актуальные проблемы развития лесного комплекса: междунар. научно-технич. конф., Вологда, 3-4 декабря 2013 г. – Вологда, 2014. – С. 62-66., Agapov A. I. Optimizaciya raskroya pilovochnika s vipilivaniem treh brusev raznoi tolschini i dvuh par bokovih dosok [Optimization of cutting logs with sawing out three beams of different thicknesses and two pairs of side boards] Aktualnie problemi razvitiya lesnogo kompleksa_ mejdunar. nauchno_tehnich. konf. [Actual problems of forest sector development: Intern. nauchno-tekhnich. Conf]. Vologda, 2014, pp. 62-66. (In Russian).

3. Агапов, А. И. Влияние ширины пропила на оптимальные размеры брусьев и досок при раскрое пиловочника с выпиливанием трёх брусьев одинаковой толщины и четырёх пар боковых досок [Электронный ресурс] / А. И. Агапов // Лесотехнический журнал. – 2014. – Т. 4. – № 2. – C. 128-135., Agapov A. I. Vliyanie shirini propila na optimalnie razmeri brusev i dosok pri raskroe pilovochnika s vipilivaniem treh brusev odinakovoi tolschini i chetireh par bokovih dosok [Influence of the width of cut on the optimum size of the boards and the boards when cutting logs with three sawing boards of the same thickness, and four pairs of side boards] Lesotehnicheskii jurnal, 2014, Vol. 4, no. 2, pp. 128-135. (In Russian).

4. Аксенов, П. П. Теоретические основы раскроя пиловочного сырья [Текст] / П. П. Аксенов. – М. : Лесн. пром-сть, 1980. – 216 с., Aksenov P. P. Teoreticheskie osnovi raskroya pilovochnogo sirya [Theoretical Foundations of cutting sawlogs]. Moscow, 1980, 216 p. (In Russian).

5. Ветшева, В. Ф. Раскрой крупномерных бревен на пиломатериалы [Текст] / В. Ф. Ветшева. – М. : Лесн. пром-сть, 1976. – 168 с., Vetsheva V. F. Raskroi krupnomernih breven na pilomateriali. [Cutting large-sized logs for lumber] Moscow, 1976, 168 p. (In Russian).