SPECIFIC FEATURES OF THERMAL PROCESSES IN DOUBLE-SIDED FACE GRINDING MACHINES-Reference-Cited by-同舟云学术

SPECIFIC FEATURES OF THERMAL PROCESSES IN DOUBLE-SIDED FACE GRINDING MACHINES

Published:2021-02-04 Issue:1 Volume:6 Page:82-94
ISSN:2071-7318
Container-title:Bulletin of Belgorod State Technological University named after. V. G. Shukhov
language:en
Short-container-title:

Author:

Nikitina I.¹,Polyakov A.¹

Affiliation:

1. Orenburg State University

Abstract

The paper presents an analysis of thermal processes in the bearing system of a double-sided face grinding machine. Experimental data on temperatures and displacements obtained when the machine is idling and when imitating the grinding process with the help of electric heaters of various powers are used for analysis. The performed studies have shown that thermal deformations of double-sided face grinding machines with an arc trajectory of workpiece feed occur in a wide range in magnitude and direction. It can violate the main requirement for the precise operation of the machine - the symmetry of processing conditions at both ends of the workpiece. From the experiments, the absolute value of the non-parallelism of the grinding wheels after three hours of operation is established; it is almost twice the value of the removed allowance. Analysis of the kinetic change in the deformations of the supporting system of the machine tool during operation under thermal load shows that as it warms up, the relative position of the grinding wheels gradually changes from the state "wider at the bottom" to the state "narrower below". This leads to a spontaneous change in the dynamic tuning of the technological system and a corresponding change in the processing accuracy. Changes in the dynamic tuning of the technological system with varying intensity continue throughout the entire operating time of the machine.

Publisher

BSTU named after V.G. Shukhov

Subject

Psychiatry and Mental health,Neuropsychology and Physiological Psychology

Reference20 articles.

1. Luk’yanov K.Y. More efficient grinding of conical roller-bearing surfaces by the end of a discontinuous wheel // Russ. Engin. Res. 2011. Vol. 31. Pp. 185–186., Luk’yanov K.Y. More efficient grinding of conical roller-bearing surfaces by the end of a discontinuous wheel. Russ. Engin. Res. 2011. Vol. 31. Pp. 185–186.

2. Jurko J., Panda A., Valíček J., Harničárová M., Pandová I. Study on cone roller bearing surface roughness improvement and the effect of surface roughness on tapered roller bearing service life // Int. J. Adv. Manuf. Technol. 2016. Vol. 82. Pp. 1099–1106., Jurko J., Panda A., Valíček J., Harničárová M., Pandová I. Study on cone roller bearing surface roughness improvement and the effect of surface roughness on tapered roller bearing service life. Int. J. Adv. Manuf. Technol. 2016. Vol. 82. Pp. 1099–1106.

3. Jiang J., Ge P., Sun S., Wang D. The theoretical and experimental research on the bearing inner ring raceway grinding process aiming to improve surface quality and process efficiency based on the integrated grinding process model // Int. J. Adv. Manuf. Technol. 2017. Vol. 93. Pp.747–765., Jiang J., Ge P., Sun S., Wang D. The theoretical and experimental research on the bearing inner ring raceway grinding process aiming to improve surface quality and process efficiency based on the integrated grinding process model. Int. J. Adv. Manuf. Technol. 2017. Vol. 93. Pp.747–765.

4. Yu G., Wang Q., Song Z., Fang D., Li Y., Yao Y. Toward the temperature distribution on ball bearing inner rings during single-grit grinding // Int. J. Adv. Manuf. Technol. 2019. Vol. 102. Pp. 957–968., Yu G., Wang Q., Song Z., Fang D., Li Y., Yao Y. Toward the temperature distribution on ball bearing inner rings during single-grit grinding. Int. J. Adv. Manuf. Technol. 2019. Vol. 102. Pp. 957–968.

5. Zhao B., Guo X., Yin L., Chang B., Li P., Wang X. Surface quality in axial ultrasound plunging-type grinding of bearing internal raceway // Int. J. Adv. Manuf. Technol. 2020. Vol. 106. Pp. 4715–4730., Zhao B., Guo X., Yin L., Chang B., Li P., Wang X. Surface quality in axial ultrasound plunging-type grinding of bearing internal raceway. Int. J. Adv. Manuf. Technol. 2020. Vol. 106. Pp. 4715–4730.

Cited by 3 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. EXPERIMENTAL MEASURES TO IMPROVE THERMAL CHARACTERISTICS IN DOUBLE-SIDED FACE GRINDING MACHINES;Bulletin of Belgorod State Technological University named after. V. G. Shukhov;2022-09-16

2. SIMULATION OF THE THERMAL DEFORMATION BEHAVIOR OF DOUBLE SIDED FACE GRINDERS;Bulletin of Belgorod State Technological University named after. V. G. Shukhov;2022-01-18

3. The Prospects of Abrasive Treatment of Tough-To-Machine Materials;Multidisciplinary Aspects of Production Engineering;2021-09-01