Author:
Tomczak Sandra J.,Marchant Darrell,Svejda Steve,Minton Timothy K.,Brunsvold Amy L.,Gouzman Irina,Grossman Eitan,Schatz George C.,Troya Diego,Sun LiPeng,Gonzalez Rene I.
Abstract
ABSTRACTKapton polyimide (PI) is widely used on the exterior of spacecraft as a thermal insulator. Atomic oxygen (AO) in lower earth orbit (LEO) causes severe degradation in Kapton resulting in reduced spacecraft lifetimes. One solution is to coat the polymer surface with SiO2 since this coating is known to impart remarkable oxidation resistance. Imperfections in the SiO2 application process and micrometeoroid / debris impact in orbit damage the SiO2 coating, leading to erosion of Kapton.A self passivating, self healing silica layer protecting underlying Kapton upon exposure to AO may result from the nanodispersion of silicon and oxygen within the polymer matrix. Polyhedral oligomeric silsesquioxane (POSS) is composed of an inorganic cage structure with a 2:3 Si:O ratio surrounded by tailorable organic groups and is a possible delivery system for nanodispersed silica. A POSS dianiline was copolymerized with pyromellitic dianhydride and 4, 4′-oxydianiline resulting in POSS Kapton Polyimide. The glass transition temperature (Tg) of 5 to 25 weight % POSS Polyimide was determined to be slightly lower, 5 – 10 %, than that of unmodified polyimides (414 °C). Furthermore the room temperature modulus of polyimide is unaffected by POSS, and the modulus at temperatures greater than the Tg of the polyimide is doubled by the incorporation of 20 wt % POSS.To simulate LEO conditions, POSS PI films underwent exposure to a hyperthermal O-atom beam. Surface analysis of exposed and unexposed films conducted with X-ray photoelectron spectroscopy, atomic force microscopy, and surface profilometry support the formation of a SiO2 self healing passivation layer upon AO exposure. This is exemplified by erosion rates of 10 and 20 weight % POSS PI samples which were 3.7 and 0.98 percent, respectively, of the erosion rate for Kapton H at a fluence of 8.5 × 1020 O atoms cm-2. This data corresponds to an erosion yield for 10 wt % POSS PI of 4.8 % of Kapton H. In a separate exposure, at a fluence of 7.33 × 1020 O atoms cm-2, 25 wt % POSS Polyimide showed the erosion yield of about 1.1 % of that of Kapton H. Also, recently at a lower fluence of 2.03 × 1020 O atoms cm-2, in going from 20 to 25 wt % POSS PI the erosion was decreased by a factor of 2 with an erosion yield too minor to be measured for 25 wt % POSS PI.
Publisher
Springer Science and Business Media LLC
Reference26 articles.
1. 1. de Groh K. K. , Banks B. A. , “Techniques for Measuring Low Earth Orbital Atomic Oxygen Erosion of Polymers,” 2002 Symposium and Exhibition sponsored by the Society for the Advancement of Materials and Process Engineering, Long Beach, CA, May 12–16, 2002.
2. Protective coatings for spacecraft materials
3. EOIM-III mass spectrometry and polymer chemistry - STS 46, July-August 1992
4. An Investigation of the Resistance of Polyhedral Oligomeric Silsesquioxane Polyimide to Atomic-Oxygen Attack
Cited by
8 articles.
订阅此论文施引文献
订阅此论文施引文献,注册后可以免费订阅5篇论文的施引文献,订阅后可以查看论文全部施引文献