Effect of Milling Time and Reinforcement Volume Fraction on Microstructure and Mechanical Properties of SiCp-Reinforced AA2017 Composite Powder Produced by High-Energy Ball Milling

Author:

Gasha Shimelis Bihon1ORCID,Trautmann Maik1ORCID,Wagner Guntram1ORCID

Affiliation:

1. Professorship of Composites and Material Compounds, Institute of Materials Science and Engineering (IWW), Chemnitz University of Technology, 09125 Chemnitz, Germany

Abstract

The influence of milling time and volume fraction of reinforcement on the morphology, microstructure, and mechanical behaviors of SiCp-reinforced AA2017 composite powder produced by high-energy ball milling (HEBM) was investigated. AA2017 + SiCp composite powder with different amounts of SiC particles (5, 10, and 15 vol%) was successfully prepared from gas-atomized AA2017 aluminum alloy powder with a particle size of <100 μm and silicon carbide (SiC) powder particles with an average particle size of <1 μm. An optical microscope (OM), X-ray diffraction (XRD), and scanning electron microscope (SEM) were utilized to characterize the microstructure of the milled composite powder at different milling periods. The results indicated that the SiC particles were homogeneously distributed in the AA2017 matrix after 5 h of HEBM time. The morphology of the particles transformed from a laminar to a nearly spherical shape, and the size of the milled powder particles reduced with increasing the content of SiC particles. The XRD analysis was carried out to characterize the phase constituents, crystallite size, and lattice strain of the composite powders at different milling periods. It was found that with increasing milling time and SiC volume fraction, the crystallite size of the aluminum alloy matrix decreased while the lattice strain increased. The average crystallite sizes were reduced from >300 nm to 68 nm, 64 nm, and 64 nm after 5 h of milling, corresponding to SiC contents of 5, 10, and 15 vol%, respectively. As a result, the lattice strain increased from 0.15% to 0.5%, which is due to significant plastic deformation during the ball milling process. XRD results showed a rapid decrease in crystallite size during the early milling phase, and the minimum grain size was achieved at a higher volume fraction of SiC particles. Microhardness tests revealed that the milling time has a greater influence on the hardness than the amount of SiC reinforcements. Therefore, the composite powder milled for 5 h showed an average microhardness three times higher than that of the unmilled powder particles.

Funder

German Academic Exchange Service

Deutsche Forschungsgemeinschaft

Chemnitz University of Technology

Publisher

MDPI AG

Subject

General Materials Science

同舟云学术

1.学者识别学者识别

2.学术分析学术分析

3.人才评估人才评估

"同舟云学术"是以全球学者为主线,采集、加工和组织学术论文而形成的新型学术文献查询和分析系统,可以对全球学者进行文献检索和人才价值评估。用户可以通过关注某些学科领域的顶尖人物而持续追踪该领域的学科进展和研究前沿。经过近期的数据扩容,当前同舟云学术共收录了国内外主流学术期刊6万余种,收集的期刊论文及会议论文总量共计约1.5亿篇,并以每天添加12000余篇中外论文的速度递增。我们也可以为用户提供个性化、定制化的学者数据。欢迎来电咨询!咨询电话:010-8811{复制后删除}0370

www.globalauthorid.com

TOP

Copyright © 2019-2024 北京同舟云网络信息技术有限公司
京公网安备11010802033243号  京ICP备18003416号-3