Optimization of the Spark Plasma Sintering Process for High-Volume Fraction Tungsten Carbide/Al 2025 Composites-Reference-Cited by-同舟云学术

Optimization of the Spark Plasma Sintering Process for High-Volume Fraction Tungsten Carbide/Al 2025 Composites

Published:2022-06-29 Issue: Volume:2022 Page:1-7
ISSN:1687-8442
Container-title:Advances in Materials Science and Engineering
language:en
Short-container-title:Advances in Materials Science and Engineering

Author:

Mahesha C. R.¹,R Suprabha¹,Polayya Chintada²,Rinawa Moti Lal³,Sakthi T.⁴,Munjal Neha⁵,Komalnu Raghavan Ishwarya⁶^ORCID,Ganeshan P.⁷,C Chanakyan⁸

Affiliation:

1. Department of Industrial Engineering & Management, Dr. Ambedkar Institute of Technology, Bangalore, Karnataka 560056, India

2. Department of Mechanical Engineering, Lendi Institute of Engineering and Technology, Vizianagaram, Andhra Pradesh 535005, India

3. Department of Mechanical Engineering, Government Engineering College, Jhalawar, Rajasthan 326023, India

4. Department of Mechanical Engineering, National Engineering College, Kovilpatti, Tamil Nadu 628503, India

5. Department of Physics, Lovely Professional University, Phagwara, Punjab 144411, India

6. Department of ElectroMechanical Engineering, Faculty of Manufacturing, Institute of Technology, Hawassa University, Hawassa, Ethiopia

7. Department of Mechanical Engineering, Sri Eshwar College of Engineering, Coimbatore, Tamil Nadu 641202, India

8. Department of Mechanical Engineering, Government College of Engineering, Thanjavur, Tamilnadu 613402, India

Abstract

With an orthogonal experimental design, Spark plasma sintering method was used to create tungsten carbide with Al 2025 composites. Pressure, temperature, and hold time all had an influence on the mechanical characteristics of the composites. Pressure had the greatest effect on density and bending strength, followed by temperature and holding duration. After five minutes of sintering at 556°C under 40 MPa, a 50% tungsten carbide/Al 2025 composite material was produced, resulting in a density of 997.7 percent and a spectacular bending strength of 766.65 MPa. This study revealed the ability of high-volume fraction mixes to support huge loads.

Publisher

Hindawi Limited

Subject

General Engineering,General Materials Science

Link

http://downloads.hindawi.com/journals/amse/2022/6433716.pdf

Reference32 articles.

1. Mechanical properties of Fly ash reinforced Aluminium matrix composites

2. Reactive hot pressing of ZrB2-based composites with changes in ZrO2/SiC ratio and sintering conditions. Part II: Mechanical behavior

3. Investigation on Wear Characteristics of AZ91D/Nanoalumina Composites

4. Experimental and analytical study on factors influencing biomimetic undulating fin propulsion performance based on orthogonal experimental design

5. Microstructural and tribological characterization of Al/EGG shell ash composites prepared by liquid metallurgy process;V. Mohanavel;Journal of the Balkan Tribological Association,2020

Cited by 5 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Impact of Assorted Temperature on Yield and Surface Morphology of Multiple Layers of Carbon Nanotubes by Spurt Pyrolysis Techniques;Materials Science Forum;2024-03-29

2. Investigations on Varying Compositions of Nylon 6 Polymer Matrix Composites for Wear Reduction in Application to Gears;Materials Science Forum;2024-03-29

3. Automatic Medicine Dispensing System Using IoT;Advances in Intelligent Systems and Technologies;2023-08-18

4. Retracted: Optimization of the Spark Plasma Sintering Process for High-Volume Fraction Tungsten Carbide/Al 2025 Composites;Advances in Materials Science and Engineering;2023-06-21

5. A survey on design and optimization of metallic biomaterial for orthopaedic application;INTERNATIONAL CONFERENCE ON INNOVATIONS IN ROBOTICS, INTELLIGENT AUTOMATION AND CONTROL;2023