Investigating the Material Removal Rate Parameters in ECM for Al 5086 Alloy-Reinforced Silicon Carbide/Flyash Hybrid Composites by Using Minitab-18-Reference-Cited by-同舟云学术

Investigating the Material Removal Rate Parameters in ECM for Al 5086 Alloy-Reinforced Silicon Carbide/Flyash Hybrid Composites by Using Minitab-18

Published:2021-11-03 Issue: Volume:2021 Page:1-6
ISSN:1687-8442
Container-title:Advances in Materials Science and Engineering
language:en
Short-container-title:Advances in Materials Science and Engineering

Author:

Gugulothu Bhiksha¹^ORCID,Satheesh Kumar P. S.²,Srinivas Bathula³,Ramakrishna Alapati³,Vijayakumar S.³

Affiliation:

1. Department of Mechanical Engineering, Bule Hora University, Post box no-144, Oromia, Ethiopia

2. Department of Science and Humanities, AAA College of Engineering and Technology, Sivakasi, Virudhunagar District, Tamil Nadu, India

3. Department of Mechanical Engineering, BVC Engineering College (Autonomous), Odalarevu 533210, Andhra Pradesh, India

Abstract

This study explained about machining parameters of Al5086/Flyash/Sic hybrid metal matrix composites by the Taguchi technique. Al5086 reinforced in SiC (5–10 wt %) and 8% weight of flyash are retained as constants. The specimens are prepared with the help of the stir casting method. The material removal rate was examined by electrochemical machining under various parameters such as feed rate (0.15–0.30 mm/min), voltage (10–20 V), and electrolyte concentration (20–35 g/litre). Taguchi’s L16 orthogonal array was selected for design of experiments (DOEs), and 16 experimental tests were conducted to examine the effect of the selected machining parameters employed to identify the best optimal levels and also to investigate the effect of electrochemical machining parameters on MRR determined by Minitab-18.

Publisher

Hindawi Limited

Subject

General Engineering,General Materials Science

Link

http://downloads.hindawi.com/journals/amse/2021/2079811.pdf

Reference18 articles.

1. Mechanical Behaviour of Aluminium Hybrid Metal Matrix Composites – A Review

2. Effect of Heat Treatment on Tensile Strength of Al7075/Al2O3/SiCp Hybrid Composite by Stir Casting Technique

3. Wear behavior and dry sliding tribological properties of ultra-fine grained Al5083 alloy and boron carbide-reinforced Al5083-based composite at room and elevated temperatures

4. Mechanical behavior of cast SiCp-reinforced Al-4.5%Cu-1.5%Mg alloy

5. Influence of sliding speed on the dry sliding wear behaviour and the subsurface deformation on hybrid metal matrix composite

Cited by 32 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. The effect of rotary EDM parameters on the surface integrity and geometric parameters of holes in Si3N4-TiN electro conductive ceramics using DFA-RSM-ANN method;Tribology International;2024-12

2. Prediction on partial replacement of cement and coarse aggregate by zeolite powder and steel slag in high-performance concrete;Engineering Research Express;2024-05-28

3. Taguchi Analysis for Wear Characteristics of Al6063 Alloy–Zirconium Silicate Composites;Journal of The Institution of Engineers (India): Series D;2024-03-27

4. Examination of electrochemical machining parameters for AA6082/ZrSiO4/SiC composite using Taguchi-ANN approach;International Journal on Interactive Design and Manufacturing (IJIDeM);2024-03-13

5. Effect of the hollow electrode on the material removal rate of titanium alloy (grade 1) in the electrochemical machining (ECM) process;BIO Web of Conferences;2024