Modeling of technological parameters in the milling process of polycarbonate workpieces under various processing modes-Reference-Cited by-同舟云学术

Modeling of technological parameters in the milling process of polycarbonate workpieces under various processing modes

Published:2023-02-24 Issue:2 Volume:2023 Page:26-31
ISSN:2223-4608
Container-title:Science intensive technologies in mechanical engineering
language:en
Short-container-title:

Author:

Unyanin Aleksandr¹,Dimukhametov Ilnaz²

Affiliation:

1. Ulyanovsk State Technical University

2. Ul'yanovskiy gosudarstvennyy tehnicheskiy universitet

Abstract

Computer simulation of technological parameters in the milling process of polycarbonate workpieces under various processing modes is realized. The parameters are recorded at various points in the contact time of the milling cutter tooth with the workpiece. The regularities of changes in the parameters of the milling process, including forces and temperatures in the contact zones of the facing with the cutter tooth or in case of tooth contact with the workpiece, depending on the elements of the milling mode, are found. It’s also found that the temperatures in the contact zone of the tooth with the workpiece are higher than in the contact zone of the tooth with the facing. The pattern of temperature distribution in the surface layer of the workpiece is distilled. Mathematical dependences describing the relationship of temperatures with the elements of the milling mode, are obtained

Publisher

Bryansk State Technical University BSTU

Subject

General Earth and Planetary Sciences,General Environmental Science

Reference7 articles.

1. Унянин А.Н. Аналитическое исследование температурного поля при фрезеровании с наложением ультразвуковых колебаний // Вестник РГАТУ им. П.А. Соловьева. 2017. № 2 (41). С. 220–235., Unyanin, A.N. Analytical study of the temperature field during milling with the imposition of ultrasonic vibrations / A.N. Unyanin // Vestnik RGATU im. P.A. Solovyov. – 2017. – No. 2 (41). – S. 220 – 235.

2. Резников А.Н., Резников Л.А. Тепловые процессы в технологических системах. М.: Машиностроение, 1990. 288 с., Reznikov, A.N. Thermal processes in technological systems / A.N. Reznikov, L.A. Reznikov. – M.: Mashinostroenie, 1990. – 288 p.

3. Воронцов А.Л., Султан-Заде Н.М., Албагачиев А.Ю. Разработка новой теории резания. Математическое описание образования стружки разных видов, пульсации сил резания и параметров контакта обработанной поверхности заготовки с задней поверхностью резца // Вестник машиностроения. 2008. № 7. С. 56–61., Vorontsov, A.L. Development of a new theory of cutting. Mathematical description of the formation of chips of various types, pulsations of cutting forces and parameters of contact between the machined surface of the workpiece and the rear surface of the cutter / A.L. Vorontsov, N.M. Sultan-Zade, A.Yu. Albagachiev // Bulletin of Mechanical Engineering. – 2008. – No. 7. – P. 56 – 61.

4. Воронцов А.Л., Султан-Заде Н.М., Албагачиев А.Ю. Разработка новой теории резания. Практические расчеты параметров резания при точении // Вестник машиностроения. 2008. № 9. С. 67–70., Vorontsov, A.L. Development of a new theory of cutting. Practical calculations of cutting parameters during turning / A.L. Vorontsov, N.M. Sultan-Zade, A. Yu. Albagachiev // Vestnik mashinostroeniya. – 2008. – No. 9. – P. 67 – 70.

5. Справочник инструментальщика / И.А. Ординарцев, Г.В. Филиппов, А. Н. Шевченко и др. / Под общ. ред. И.А. Ординарцева. Л.: Машиностроение, Ленинградское отделение, 1987. 846 с., Toolmaker's Handbook / I.A. Ordinartsev, G.V. Filippov, A. N. Shevchenko and others / Ed. ed. I.A. Ordinartseva. – L .: Mashinostroenie, Leningrad branch, 1987. – 846 p.