ON THE USE OF COATINGS FOR TURNING STAINLESS STEELS-Reference-Cited by-同舟云学术

ON THE USE OF COATINGS FOR TURNING STAINLESS STEELS

Published:2023-04-12 Issue:4 Volume:2023 Page:4-10
ISSN:2782-5957
Container-title:Transport engineering
language:en
Short-container-title:

Author:

Mokrickiy Bori¹^ORCID,Kosmynin Alexander²,Sablin Pavel³,Shelkovnikov Vadim⁴

Affiliation:

1. Komsomolsk-upon Amur State University

2. Komsomolsk-on-Amur State University

3. Komsomolsk-upon-Amur State University

4. Komsomol'skiy-na-Amure gosudarstvennyy universitet

Abstract

The study objective is to increase the durability period of replaceable carbide inserts by applying coatings for turning hard-to-machine stainless steels. Research results: recommendations are made on the choice of a rational coating of a metal-cutting tool, depending on its operating conditions. Conclusions: The developed coatings allow to increase the durability period of the cutting tool up to 3 times. The paper discusses the results of applying the newly developed coatings on the hard-alloy material of VK8 brand. The analysis is done for turning stainless steels of 09X17N7YU, 12X18N10T, 13X15N5AM-3 grades. The most rational coatings are found, which make it possible to increase the durability period of the metal-cutting tool up to 3 times.

Publisher

Bryansk State Technical University BSTU

Reference16 articles.

1. Криворучко Д.В. Моделирование процессов резания методом конечных элементов : методологические основы : монография / Д.В. Криворучко, В.А. Залога; под общ. Ред. В.А. Залоги.- Сумы.: Университетская книга. 2012. – 496 с., Krivoruchko DV, Zaloga VA. Modeling of cutting processes by finite element method: methodological foundations: monograph. Sumy: Universitetskaya Kniga; 2012.

2. Петрушин С.И. Стружкообразование с развитой зоной пластических деформации при резании металлов/ Известия Томского политехнического университета. 2009. Т.314. №2, с. 62., Petrushin SI. Chip formation with a developed zone of plastic deformation during metal cutting. Bulletin of the Tomsk Polytechnic University. 2009;314(2):62.

3. Петрушин С.И. Основы формообразования резанием лезвийными инструментами. – Томск: Изд-во ТПУ. 2004. – 204 с., Petrushin SI. Generation of geometry fundamentals by cutting blade tools. Tomsk: TPU Publishing House;2004.

4. Bezylagny V.F. Similarity method in mechanical engineering technology. M.: Mechanical engineering. 2012. – 320 p., Bezylagny VF. Similarity method in mechanical engineering technology. Moscow: Mashinostroenie; 2012.

5. Grigoriev S.N., Tabakov V.P., Volosova M.A. Technological methods of increasing the wear resistance of contact pads of cutting tools: monograph / S.N. Grigoriev, V.P. Tabakov, M.A. Volosova. – Stary Oskol: TNT, 2011, - 380 p., Grigoriev SN, Tabakov VP, Volosova MA. Technological methods of increasing the wear resistance of contact pads of cutting tools: monograph. Stary Oskol: TNT; 2011.

Cited by 1 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. MACHINING THE ENDS OF PART WORKPIECES;Transport engineering;2024-05-12