STUDY OF THE FRICTION FACTOR OF POLYMER MATERIALS FOR 3D PRINTING OF ROLLING STOCK STRUCTURAL ELEMENTS-Reference-Cited by-同舟云学术

STUDY OF THE FRICTION FACTOR OF POLYMER MATERIALS FOR 3D PRINTING OF ROLLING STOCK STRUCTURAL ELEMENTS

Published:2023-06-14 Issue:6 Volume:2023 Page:43-51
ISSN:2782-5957
Container-title:Transport engineering
language:en
Short-container-title:

Author:

Osipov Dmitry¹,Ivanov Pavel¹,Dulskiy Evgeny¹,Pronin Konstantin¹

Affiliation:

1. Irkutsk State Transport University

Abstract

Additive technologies are represented by various methods of 3D printing and are increasingly being used in various industries around the world. For example, printing with metal powders is used for the production of such structural elements as various arm supports in the aircraft industry or the manufacture of spacecraft hulls. The use of 3D printing with the use of polymer materials makes it possible to manufacture, for example, various gears for non-principle mechanisms. The use of such technology in pneumatics is also relevant. However, at the same time, the possibility of using these technologies for the manufacture of various pneumatic devices has not been widely studied up to now. In the course of studying this issue, a pneumatic gearbox was made. However, it was found out that one of the problems that does not allow to design and manufacture a normally functioning pneumatic device is an unknown value of friction factor of the materials of which its elements are made. The study objective is to find out the static friction factor of products made of polymer materials using 3D printing technologies. The necessity of this study is explained by the problems that arose as a result of testing a high-performance pneumatic gearbox manufactured using additive technologies applying various polymer materials. The main problem of this device is the density violation of fixed detachable joints of gearbox case parts and covers. Since the medium to be used is compressed air under a pressure of 0.9 MPa, any density violation can lead to the gearbox destruction or to air losses from the braking system of a freight train due to an increase in the number of leaks in the pipeline for additional power supply to the spare reserve. The paper presents the results of experimental studies on finding the friction factor of various types of materials used in 3D printing. The obtained friction factors are required for the design of seals of pneumatic devices according to generally accepted methods.

Publisher

Bryansk State Technical University BSTU

Reference10 articles.

1. Sorokin D.V., Babkina L.A., Brazgovka O.V. Designing various-purpose subassemblies based on topological optimization // Spacecrafts & Technologies, 2022, vol. 6, no. 2, pp. 61-82. doi: 10.26732/j.st.2022.2.01., Sorokin DV, Babkina LA, Brazgovka OV. Designing various-purpose subassemblies based on topological optimization. Spacecrafts and Technologies. 2022;6(2):61-82. doi: 10.26732/j.st.2022.2.01.

2. Galinovsky, A.L. & Filimonov, A.S. & Badanina, Y.V. & Dolgikh, A.I.. (2023). Comparative correlation study of software systems for three-dimensional numerical simulation by analyzing results of the RST product topological optimization. Proceedings of Higher Educational Institutions. Маchine Building. 42-51. 10.18698/0536-1044-2023-1-42-51., Galinovsky AL, Filimonov AS, Badanina YV, Dolgikh AI. Comparative correlation study of software systems for three-dimensional numerical simulation by analyzing results of the RST product topological optimization. Proceedings of Higher Educational Institution of Mechanical Building. 2023:42-51. 10.18698/0536-1044-2023-1-42-51.

3. Слынько, М. Д. Аддитивные технологии на железнодорожном транспорте / М. Д. Слынько, О. Л. Цветкова // Актуальные проблемы развития транспортного комплекса в условиях цифровой экономики : материалы III Международной студенческой научно-практической конференции, Нижний Новгород, 10 декабря 2021 года / филиал СамГУПС в г. Нижнем Новгороде. – Нижний Новгород: Б. и., 2021. С. 31-36. – EDN LIVRAW., Slynko MD, Tsvetkova OL. Additive technologies in railway transport. Proceedings of the III International Student Scientific and Practical Conference, December 10, 2021: Actual Problems of the Development of the Transport Complex in the Digital Economy; Branch of SamGUPS in Nizhny Novgorod. Nizhny Novgorod; 2021. EDN LIVRAW

4. Иванов, П. Ю. Снижение энергопотребления электровоза при управлении пневматическими тормозами грузового поезда / П. Ю. Иванов, А. А. Хамнаева, А. М. Худоногов // Разработка и эксплуатация электротехнических комплексов и систем энергетики и наземного транспорта : Материалы третьей международной научно-практической конференции, Омск, 06 декабря 2018 года. – Омск: Омский государственный университет путей сообщения, 2018. С. 143-151. – EDN PPBPJT., Ivanov PYu, Khamnaeva AA, Khudonogov AM. Reduction of electric locomotive energy consumption when controlling pneumatic brakes of a freight train. Proceedings of the Third International Scientific and Practical Conference, 06 December, 2018: Development and Operation of Electro-technical Complexes and Systems of Power Engineering and Ground Transport; Omsk: Omsk State University of Railways; 2018. EDN PPBPJT.

5. Study of the influence of the brake shoe temperature and wheel tread on braking effectiveness / P. Ivanov, A. Khudonogov, E. Dulskiy [et al.] // Journal of Physics: Conference Series, Voronezh, 10–13 декабря 2019 года. – Voronezh, 2020. – P. 012086. – DOI 10.1088/1742-6596/1614/1/012086. – EDN OHFFAP., Ivanov PYu, Khudonogov AM, Dulskiy E. Study of the influence of the brake shoe temperature and wheel tread on braking effectiveness. Journal of Physics: Conference Series. Voronezh; 2020. DOI 10.1088/1742-6596/1614/1/012086. – EDN OHFFAP.