INVESTIGATION OF OUTPUT PARAMETER CORRELATION OF CUTTING ENGINEERING PROCESS WITH MASS HARD-ALLOY REPLACEABLE METAL CUTTING PLATES-Reference-Cited by-同舟云学术

INVESTIGATION OF OUTPUT PARAMETER CORRELATION OF CUTTING ENGINEERING PROCESS WITH MASS HARD-ALLOY REPLACEABLE METAL CUTTING PLATES

Published:2019-10-07 Issue:9 Volume:2019 Page:36-41
ISSN:1999-8775
Container-title:Bulletin of Bryansk state technical university
language:en
Short-container-title:

Author:

Мокрицкий Борис¹,Mokritskiy Boris²,Усова Татьяна³,Usova Tat'yana²,Шакирова Ольга⁴,Shakirova Ol'ga²,Усанов Геннадий⁴,Usanov Gennadiy²

Affiliation:

1. Комсомольский-на-Амуре государственный технический университет

2. Komsomolsk-upon-Amur State University

3. Космсомольский-на-Амуре государственный университет

4. Комсомольск-на-Амуре государственный университет

Abstract

It is possible to assume physical properties or stress-strain characteristics of material as a basis of diagnostics of a machine tool system state on the basis of which to forecast a level of engineering process updating for product blank machining and to optimize tool parameters and other equipment components ensuring efficient machining processes economically and technically. The purpose of the work: according to the measurement results of the mass of replaceable hard-alloy cutting plates of a metal-cutting tool to draw a conclusion of their operational capability under those or other operational conditions at a standard engineering enterprise. There are considered standard designs of cutting and chip breaking plates. The mass measurements of more than 250 plates are carried out. The procedure for the plate selection according to quality is developed. The results obtained are tabulated and illustrated. A share ratio of suitable and scrap plates is shown. There are formulated recommendations regarding suitable plates use depending on their quality grade.

Publisher

Bryansk State Technical University BSTU

Subject

General Earth and Planetary Sciences,General Environmental Science

Reference6 articles.

1. Vereschaka, А. Two-component end mills with multilayer composite nano-structured coatings as a viable alternative to monolithic carbide end mills / A. Vereschaka, B. Mokritskii, E. Mokritskaya, O. Sharipov, M. Oganyan // Mechanics & Industry 18, 705 (2017). - https://doi.org/10.1051/meca/2017052., Vereschaka, A. Two-component end mills with multilayer composite nano-structured coatings as a viable alternative to monolithic carbide end mills / A. Vereschaka, B. Mokritskii, E. Mokritskaya, O. Sharipov, M. Oganyan // Mechanics & Industry 18, 705 (2017). - https://doi.org/10.1051/meca/2017052.

2. Mokritskii, B.Ja. Results in kompostite hard-aliou and milts desingn baset on simulation of their operationconditions / B.Ja. Mokritskii, А.V. Morozova, T.J. Usova // International conference on industrial ingeneering. - 2017. - Т. 206. - Р. 1093-1098. - (Series of books «Procedia Ingeenering»)., Mokritskii, B.Ja. Results in kompostite hard-aliou and milts desingn baset on simulation of their operationconditions / B.Ja. Mokritskii, A.V. Morozova, T.J. Usova // International conference on industrial ingeneering. - 2017. - T. 206. - R. 1093-1098. - (Series of books «Procedia Ingeenering»).

3. Vereschaka, А. Increase in Efficiency of tnd Milling of titanium alloys die to tools with miltilayered composite nano-structured Zr-ZrN-(Zr,Al)N and Zr-ZrN-(Zr,Cr,Al)N coatings / A. Vereschaka, M. Oganyan, Yu. Bublikov, N. Sitnikov, K. Deev, V. Pupchin, B. Mokritskii // Coating 8, 395 (2018). - doi:10.3390/coatings8110395., Vereschaka, A. Increase in Efficiency of tnd Milling of titanium alloys die to tools with miltilayered composite nano-structured Zr-ZrN-(Zr,Al)N and Zr-ZrN-(Zr,Cr,Al)N coatings / A. Vereschaka, M. Oganyan, Yu. Bublikov, N. Sitnikov, K. Deev, V. Pupchin, B. Mokritskii // Coating 8, 395 (2018). - doi:10.3390/coatings8110395.

4. Чирков, А.П. Роль метрологического обеспечения в инновационной деятельности / А.П. Чирков // Главный метролог. - 2013. - № 1. - С. 20-24., Chirkov, A.P. Rol' metrologicheskogo obespecheniya v innovacionnoy deyatel'nosti / A.P. Chirkov // Glavnyy metrolog. - 2013. - № 1. - S. 20-24.

5. Чирков, А.П. Инфраструктурное обеспечение внедрения наукоёмких технологий: монография / А.П. Чирков, А.А. Алисов [и др.] // Социально-экономические аспекты технологической модернизации современного машиностроительного производства. - М.: Спектр, 2013. - С. 78-120., Chirkov, A.P. Infrastrukturnoe obespechenie vnedreniya naukoemkih tehnologiy: monografiya / A.P. Chirkov, A.A. Alisov [i dr.] // Social'no-ekonomicheskie aspekty tehnologicheskoy modernizacii sovremennogo mashinostroitel'nogo proizvodstva. - M.: Spektr, 2013. - S. 78-120.