Numerical Investigation of Mold Heating Power and Time in Metal Layered Composite Production-Reference-Cited by-同舟云学术

Numerical Investigation of Mold Heating Power and Time in Metal Layered Composite Production

Published:2023-09-28 Issue:3 Volume:12 Page:829-841
ISSN:2147-3129
Container-title:Bitlis Eren Üniversitesi Fen Bilimleri Dergisi
language:
Short-container-title:

Author:

KAMER Muhammed Safa¹^ORCID,ÇUTAY Arif²^ORCID,TEMİZ Şemsettin³^ORCID,KAYA Ahmet¹^ORCID

Affiliation:

1. KAHRAMANMARAŞ SÜTÇÜ İMAM ÜNİVERSİTESİ

2. KAHRAMANMARAŞ SÜTÇÜ İMAM ÜNİVERSİTESİ, MÜHENDİSLİK-MİMARLIK FAKÜLTESİ

3. İNÖNÜ ÜNİVERSİTESİ

Abstract

Curing time of epoxy resin is an important phenomenon in the production of metal layered composites. In order to reduce the curing time, the heating of the mold and epoxy was carried out in this study and numerically investigated on time dependent. The most consistent mesh structure was chosen among five different mesh number in terms of difference between temperature results. 10 different cases were created to examine different heater powers and different operating patterns. The results were examined by creating a temperature-time graph and contours showing the temperature distribution. As the number of cartridges and heater power increase, higher temperatures are reached in a shorter time. Even with the same heater power, different operating patterns can lead to differences in results in terms of temperature. Different operating pattern was seen as an independent parameter in heater power for obtaining a homogeneous temperature distribution.

Publisher

Bitlis Eren Universitesi Fen Bilimleri Dergisi

Subject

Earth-Surface Processes

Reference20 articles.

1. [1] S. Kaveloğlu and Ş. Temiz, “An experimental and finite element analysis of 3D printed honeycomb structures under axial compression,” Polymers & Polymer Composites, vol. 30, p. 096739112211223, Jan. 2022.

2. [2] A. Saylik and Ş. Temiz, “Low-speed impact behavior of fiber-reinforced polymer-based glass, carbon, and glass/carbon hybrid composites,” MP MATERIALPRUEFUNG - MP MATERIALS TESTING, vol. 64, no. 6, pp. 820–831, Jun. 2022.

3. [3] S. Kaveloğlu, Ş. Temiz, O. Doğan, and M. S. Kamer, “Investigation of Bending Strength of Honeycomb Sandwich Structures with Different Cell Diameters Produced by 3D Printer,” Çukurova Üniversitesi Mühendislik Fakültesi Dergisi, vol. 37, no. 2, pp. 459–470, Jun. 2022.

4. [4] M. Yilmaz, N. F. Yilmaz, and M. F. Kalkan, “Rheology, crystallinity, and mechanical investigation of interlayer adhesion strength by thermal annealing of polyetherimide (PEI/ULTEM 1010) parts produced by 3D printing,” Journal of Materials Engineering and Performance, vol. 31, no. 12, pp. 9900–9909, Jun. 2022.

5. [5] B. Liu, S. Bickerton, and S. G. Advani, “Modelling and simulation of Resin Transfer Moulding (RTM)—gate control, venting and dry spot prediction,” Composites Part A: Applied Science and Manufacturing, vol. 27, no. 2, pp. 135–141, 1996.