Influence of Powder Charge Composition on the Structure and Properties of T15K6 Hard Alloy-Reference-Cited by-同舟云学术

Influence of Powder Charge Composition on the Structure and Properties of T15K6 Hard Alloy

Published:2023-07-23 Issue:2 Volume:13 Page:20-42
ISSN:2223-1528
Container-title:Proceedings of the Southwest State University. Series: Engineering and Technology
language:
Short-container-title:jour

Author:

Alimzhanova А. М.¹,Eremeeva Zh. V.²^ORCID,Nozhkina A. V.²,Levina V. V.²,Nitkin N. M.³,Orlov V. L.³

Affiliation:

1. RSE National Center on Complex Processing of Mineral Raw Materials of the Republic of Kazakhstan

2. National Research University MISIS

3. Moscow Polytechnic University

Abstract

The purpose of the study is to determine the effect of nanosized additives on the structure and properties of the T15K6 hard alloy.Methods. These studies were carried out using an S-3400N electron microscope. The mechanical and physical properties of the structure of a hard alloy of the WC-TiC-Co system were studied using the example of T15K6 when nanosized tungsten powder and nanosized tungsten carbide powder with cobalt deposited on it were introduced into the initial charge using an optical and electron microscope; An X-ray spectrum analysis of the obtained samples of the T15K6 hard alloy was carried out on a DRON-4 X-ray diffractometer.Results. A hard alloy of the WC-TiC-Co system was studied with the introduction of nanosized tungsten powder into the initial charge, as well as with the introduction of nanosized tungsten carbide with cobalt deposited on its surface.In the work, the used powders of tungsten, nano-tungsten, cobalt, titanium carbide, tungsten carbide, nano-powder of tungsten carbide were studied, and the microstructure of the obtained hard alloys was also studied. It is shown that the coercive force of the T15K6 alloy depends on the size of the cobalt phase regions in the alloy; measuring its value makes it possible to judge the size of carbide grains. To improve the strength properties of hard alloys of the WC-TiCCo system, it is recommended to introduce nanosized WC additives or WC nanopowder with deposited cobalt.Conclusion. To improve the strength properties of hard alloys of the WC-TiC-Co system, it is recommended to introduce nanosized WC additives or WC nanopowder with deposited cobalt. The introduction of these additives into the composition of the powder charge of the T15K6 hard alloy leads to an increase in the ultimate bending strength by 15%. The introduction of nanosized WC additives or WC nanopowder with deposited cobalt makes it possible to obtain a fine-grained structure with a grain size of no more than 4–6 μm.

Publisher

Southwest State University

Reference31 articles.

1. Fal'kovskiy V. A., Klyachko L. I. Tverdye splavy [Hard alloys]. Moscow, Ruda i metally Publ., 2005. 413 р.

2. Andrievskiy R. A., Ragulya A. V. Nanostrukturnye materialy [Nanostructured materials]. Moscow, AKADEMA Publ., 2005. 178 р.

3. Park Y. J., Hwang N. M., Yoon D. Y. Abnormal growth of faceted (WC) grains in a (Co) liquid matrix. Metallurgical and Materials Transactions A, 1996, vol. 27, is. 9, pp. 2809–2819.

4. Janisch D., Reichel B. B. [The way of tungsten carbide formation by gas phase corbonization]. Patent Germany, no. 198.52.459, 2000.

5. Mccandlish L. E., Kear B. H., Bhatia S. J. Mixing tungsten and cobalt compounds, drying to form homogeneous precursor powder, thermochemically converting in carburizing gas. Patent US, no. 5352269 A. 1994.