Factors Affecting Torque for a Roller Cone Bit

Author:

Warren T.M.

Abstract

Warren, T.M., SPE, Amoco Production Co. Summary Several authors have presented theoretical bit torque relationships derived by equating the energy required to rotate a bit to the energy required to remove a unit volume of rock (energy balance concept). This approach has had little quantitative success in predicting bit torque because of difficulties in quantifying both the drilling efficiency and the specific energy of the rock under a given set of conditions. A torque relationship based on a force balance concept is presented to minimize the problems with the energy-based relationships. The new torque relationship shows that for a given bit, the torque is determined largely by the applied weight on bit (WOB) and the depth of tooth penetration. The model is insensitive to moderate changes in factors such as bit hydraulics, fluid type, and formation type. Laboratory drilling tests and field data were used to confirm the validity of the new torque model. Introduction The torque required to rotate a roller cone bit is of interest for several reasons. First, it may give information about the formation being drilled and the condition of the bit. Second, bit torque exerts a significant influence on the "bit walk" experienced in directional wells. Finally, a prediction of bit torque may be useful in matching a bit and mud motor for optimal performance. Previous work relating to bit torque has been based either on a theoretical energy balance at the bit or on an empirical correlation. The following discussion points out the major problems with these techniques and presents an alternative approach. Energy Balance Concept. The literature has several references that discuss the energy utilized by a roller cone bit in drilling rock . These articles typically relate the mechanical work done by the bit to the energy required to crush a given volume of rock. The specific energy of a rock is the minimum energy required to crush a unit volume of rock and is considered a fundamental property of the rock. The energy required to crush the volume of rock drilled in a unit increment of time is then expressed as (1) where E, is specific energy of the rock, d is hole diameter, and R is the rate of penetration (ROP). The total work done by the bit in the same unit time interval is given by (2) where W is axial force applied to the bit, N is rotary speed, and M is torque applied to the bit. The bit torque used in Eq. 2 and throughout this paper is the time-averaged torque required to rotate the bit under steady-state conditions. Eq. 2 includes both the axial and rotary work done by the bit. Generally the axial work is much less than the rotary work and therefore is neglected, but for exactness it is retained in the following discussion. Not all the energy applied to a bit is effective in creating new borehole volume. The amount of energy used to crush a fixed volume of rock is strongly related to the size of chips generated. Some energy is dissipated into the unbroken rock around the borehole while the rock stress is being increased sufficiently to form chips. Energy may be used to further reduce the chip size and remove the broken rock from under the bit. Energy is required not only to form and to remove the chips, but also to form a particular hole geometry. The total work done by the bit (Eq. 2) can be equated to the energy required to break the rock drilled in a unit of time (Eq. 1) by adding an efficiency factor, n, to account for nonproductive energy loss. This relationship can be arranged to give an equation for bit torque, (3) The usefulness of Eq. 3 depends largely on n having a reasonably constant value or at least a value that can be determined from other known parameters. Controlled drilling tests indicate that n varies enough to make the energy balance approach suspect. Figs. 1 and 2 show two sets of laboratory drilling data for an 8 3/4-in. [22.2-cm] Intl. Assn. of Drilling Contractors (IADC) Series 1-2-1 bit and an 8 1/2 -in. [21.6-cm] IADC Series 5–1-7 bit. These data were collected while drilling with the full-scale laboratory drilling rig described in Ref. 7. The Series 1–2-1 bit data in Fig. 1 were obtained while drilling Carthage marble using water as the drilling fluid. The Series 5–1-7 bit data shown in Fig. 2 were obtained with a 9.0-lbm/gal [1078-kg/m ] bentonite mud while drilling Indiana limestone. JPT P. 1500^

Publisher

Society of Petroleum Engineers (SPE)

Subject

Strategy and Management,Energy Engineering and Power Technology,Industrial relations,Fuel Technology

同舟云学术

1.学者识别学者识别

2.学术分析学术分析

3.人才评估人才评估

"同舟云学术"是以全球学者为主线,采集、加工和组织学术论文而形成的新型学术文献查询和分析系统,可以对全球学者进行文献检索和人才价值评估。用户可以通过关注某些学科领域的顶尖人物而持续追踪该领域的学科进展和研究前沿。经过近期的数据扩容,当前同舟云学术共收录了国内外主流学术期刊6万余种,收集的期刊论文及会议论文总量共计约1.5亿篇,并以每天添加12000余篇中外论文的速度递增。我们也可以为用户提供个性化、定制化的学者数据。欢迎来电咨询!咨询电话:010-8811{复制后删除}0370

www.globalauthorid.com

TOP

Copyright © 2019-2024 北京同舟云网络信息技术有限公司
京公网安备11010802033243号  京ICP备18003416号-3