Structure and microhardness of binding for diamond tools based on tungsten carbide obtained by impregnation of iron-carbon melt-Reference-Cited by-同舟云学术

Structure and microhardness of binding for diamond tools based on tungsten carbide obtained by impregnation of iron-carbon melt

Published:2021-02-12 Issue:4(104) Volume: Page:95-108
ISSN:1994-6716
Container-title:Voprosy Materialovedeniya
language:
Short-container-title:Vopr. materialoved.

Author:

Sharin P. P.¹,Akimova M. P.¹,Yakovleva S. P.¹,Popov V. I.²

Affiliation:

1. V.P. Larionov Institute of the Physical-Technical Problems of the North of the Siberian Branch of the RAS, Federal Research Centre “The Yakut Scientific Centre of the SB of the RAS”

2. M.K. Ammosov North-Eastern Federal University

Abstract

In this work, an experimental modeling of the technology for producing a matrix by sintering a diamond-containing briquette with a filler of tungsten monocarbide powder impregnated with a Fe-C eutectic melt in a vacuum is carried out. The microstructure, elemental and phase compositions of the products formed in the process of sintering a diamond-containing matrix with impregnation with a Fe-C eutectic melt in vacuum have been studied by scanning electron microscopy, X-ray spectral and X-ray phase analyzes, and Raman spectroscopy. It was found that the matrix consists of 61.0% tungsten carbide phases, 17.0% of iron carbide, 16.5% of α-Fe, and 5.5% of graphite. The eutectic Fe-C alloy, which serves as a matrix binder, consists of a ferrite-pearlite metal base with graphite inclusions. It is shown that at the diamond - matrix interface, graphite inclusions are formed not as a continuous layer, but as discontinuous areas along the perimeter of diamond grains. The microhardness of the WC-based matrix impregnated with the Fe-C melt is ~ 11 GPa, which is more than 3 times higher than the microhardness of the WC-Co-Cu hard alloy matrix obtained by sintering with copper impregnation.The research results can be used in the development of technology for the manufacture of wear-resistant matrices of diamond tools of a wide class used in the processing of materials with a high level of hardness.

Publisher

FSUE CRISM Prometey

Reference22 articles.

1. Bakul, V.N., Nikitin, Yu.I., Vernik, E.B., Selekh, V.F., Osnovy proektirovaniya i tekhnologiya izgotovleniya abrazivnogo i almaznogo instrumenta [Basics of designing and technology of manufacturing of the abrasive and diamond tool], Moscow: Mashinostroenie, 1975.

2. Novikov, N.V., Bondarenko, N.A., Zhukovsky, A.N., Mechnik, V.A., Vliyanie diffuzii i khimicheskikh reaktsiy na strukturu i svoistva burovykh vstavok. 1: Kineticheskoe opisanie sistem Calmaz-VK6 i Calmaz-(VK6-CrB2-W2B5) [The effect of diffusion and chemical reactions on the structure and properties of drill bit inserts. 1: Kinetic description of systems Cdiamond-VK6 и Cdiamond-(VK6-CrB2-W2Bs], Fizicheskaya mezomekhanika, 2005, V. 8, No 2, pp. 99-106.

3. Novikov, N.V., Bondarenko, N.A., Zhukovsky, A.N., Mechnik, V.A., Vliyanie diffuzii i khimicheskikh reaktsiy na strukturu i svoistva burovykh vstavok. 2: Rezultaty attestatsii strukturnogo sostoyaniya sverkhtverdykh materialov sostava almaz-tverdy splav VK6 [The effect of diffusion and chemical reactions on the structure and properties of drill bit inserts. 2. Evaluation results for the structural state of superhard materials of composition diamond - hard alloy VK6], Fizicheskaya mezomekhanika, 2006, V. 9, No 2, pp. 107-116.

4. Vityaz, P.A., Zhornik, V.I., Kukareko, V.A., Issledovanie strukturno-fazovogo sostoyaniya i svoystv spechennykh splavov, modernizirovannykh nanorazmernymi almazosoderzhaschimi dobavkami [A research of structural-phase state and properties of sintered alloys modified by nano-sized diamond containing additives], Izvestiya natsionalnoy akademii nauk Belarusi, Physical-technical series, 2011, No 3, pp. 5-17.

5. Artini, C., Muolo, M.L., Passerone, A., Diamond-metal interfaces in cutting tools: a review, Journal of Materials Science, 2012, V. 47 (7), pp. 3252-3264.