Adhesion of epoxy compaund to aluminum bronze

Author:

Tsvetkov Yuriy Nickolayevich1,Vlasov Mikhail Yur'evich2,Fiaktistov Yaroslav Olegovich1

Affiliation:

1. Admiral Makarov State University of Maritime and Inland Shipping

2. Lumex LLC

Abstract

The possibility to heighten the adhesion of the epoxy coating to metal surface by varying the hardener content was investigated. The experiments were conducted on the epoxy composition made up of modified epoxy resin K-153 and hardener (polyethylene polyamine). The prepared compositions contained the following percentage of the hardener: 6.1, 7.0, 7.7, 8.3, 9.5, 10.7, 11.9 and 13.0% by volume. Two series of the experiments were carried out. The goal of the first one was to evaluate the degree of the completeness of epoxy oligomers spatial stitching in hardening. The evaluation was indirect and consisted in measuring the acoustic impedance of the compositions. The second series was carried out to determine the adhesion of the epoxy compositions to bronze BrAZhNMts9-4-4-1, similar by make-up to the bronze BrA9Zh4N4L, used to manufacture ship propellers. The compositions were applied over the plates made of the bronze BrAZhNMts9-4-4-1, the plates were preliminary ground to obtain the values of the roughness parameter Ra of the working surface ranged from 0.5 to 0.9 μm. The stress was measured to break the hardened epoxy coatings off the bronze plate. The results showed that the break-off stress changes with the hardener contents just the opposite way as the epoxy coating acoustic impedance does, and the less completed the process of cross-linking the higher the adhesion of the epoxy coating to the bronze surface. When the hardener content exceeds 9.5-10% by volume the values of adhesion strength and acoustic impedance stop varying: break-off stress takes on a constant minimum value, and acoustic impedance takes on a constant maximum value. In decreasing the hardener content lower than 9.5-10% by volume the adhesion begins to rise. An increase in adhesion is accounted for by an increase in the relative fraction of the epoxy groups with the decrease in hardener concentration. With a decrease in hardener content the scatter of the adhesion values multiplies, the latter is explained by the rise in the epoxy properties sensitivity to hardening conditions with a decrease in the quantity of the hardener.

Publisher

Astrakhan State Technical University

Reference17 articles.

1. Buketov A., Smetankin S., Maruschak P., Yurenin K., Sapronov O., Matvyeyev V., Menou A. New black-filled epoxy coatings for repairing surface of equipment of marine ships // Transport. 2020. V. 35. Iss. 6. P. 679–690. https://doi.org/10.3846/transport.2020.14286., Buketov A., Smetankin S., Maruschak P., Yurenin K., Sapronov O., Matvyeyev V., Menou A. New black-filled epoxy coatings for repairing surface of equipment of marine ships. Transport, 2020, vol. 35, iss. 6, pp. 679-690. https://doi.org/10.3846/transport.2020.14286.

2. Тихомиров А. В. Прогрессивные технологические процессы применения полимеров в судостроении и судоремонте. Основы технологии. Н. Новгород: ЦКБ НПО «Судоремонт», 1995. 164 с., Tikhomirov A. V. Progressivnye tekhnologicheskie protsessy primeneniia polimerov v sudostroenii i sudoremonte. Osnovy tekhnologii [Progressive technological processes of polymer application in shipbuilding and ship repair. Fundamentals of technology]. Nizhnii Novgorod, TsKB NPO «Sudoremont», 1995. 164 p.

3. Фиактистов Я. О. Ремонт гребных винтов, изношенных при кавитации, с применением полимерных составов // Современные тенденции и перспективы развития водного транспорта России: материалы X Межвуз. науч.-практ. конф. аспирантов, студентов и курсантов (Санкт-Петербург, 22 мая 2019 г.). СПб.: Изд-во ГУМРФ им. адм. С. О. Макарова, 2019. C. 279–282., Fiaktistov Ia. O. Remont grebnykh vintov, iznoshennykh pri kavitatsii, s primeneniem polimernykh sostavov. Sovremennye tendentsii i perspektivy razvitiia vodnogo transporta Rossii [Repair of propellers worn out during cavitation using polymer compounds. Current trends and prospects for the development of water transport in Russia]. Materialy X Mezhvuzovskoi nauchno-prakticheskoi konferentsii aspirantov, studentov i kursantov (Sankt-Peterburg, 22 maia 2019 g.). Saint Petersburg, Izd-vo GUMRF imeni admirala S. O. Makarova, 2019. Pp. 279-282.

4. Георгиевская Е. П. Кавитационная эрозия гребных винтов и методы борьбы с ней. Л.: Судостроение, 1978. 206 с., Georgievskaia E. P. Kavitatsionnaia eroziia grebnykh vintov i metody bor'by s nei [Cavitation erosion of propellers and methods of combating it]. Leningrad, Sudostroenie Publ., 1978. 206 p.

5. Цветков Ю. Н. Кавитационное изнашивание металлов и оборудования. СПб.: Изд-во СПбГПУ, 2003. 155 с., Tsvetkov Iu. N. Kavitatsionnoe iznashivanie metallov i oborudovaniia [Cavitation wear of metals and equipment]. Saint Petersburg, Izd-vo SPbGPU, 2003. 155 p.

同舟云学术

1.学者识别学者识别

2.学术分析学术分析

3.人才评估人才评估

"同舟云学术"是以全球学者为主线,采集、加工和组织学术论文而形成的新型学术文献查询和分析系统,可以对全球学者进行文献检索和人才价值评估。用户可以通过关注某些学科领域的顶尖人物而持续追踪该领域的学科进展和研究前沿。经过近期的数据扩容,当前同舟云学术共收录了国内外主流学术期刊6万余种,收集的期刊论文及会议论文总量共计约1.5亿篇,并以每天添加12000余篇中外论文的速度递增。我们也可以为用户提供个性化、定制化的学者数据。欢迎来电咨询!咨询电话:010-8811{复制后删除}0370

www.globalauthorid.com

TOP

Copyright © 2019-2024 北京同舟云网络信息技术有限公司
京公网安备11010802033243号  京ICP备18003416号-3