Distribution of temperature fields and specific reductions at grinding balls rolling-Reference-Cited by-同舟云学术

Distribution of temperature fields and specific reductions at grinding balls rolling

Published:2019-08-08 Issue:7 Volume:75 Page:834-839
ISSN:2619-0753
Container-title:Ferrous Metallurgy. Bulletin of Scientific , Technical and Economic Information
language:
Short-container-title:Černaâ metallurgiâ. Bûlletenʹ naučno-tehničeskoj informacii

Author:

Rubtsov V. Yu.¹,Shevchenko O. I.²,Kurochkin V. V.³,Oparin A. S.³

Affiliation:

1. JSC “EVRAZ Nighny Tagil steel-works”; Ural Federal University after the First President of Russia B.N. El’tsin

2. Nighny Tagil Technological Institute (branch), Ural Federal University after the First President of Russia B.N. El’tsin

3. JSC “EVRAZ Nighny Tagil steel-works”

Abstract

During the high hardness grinding balls production the following to the process parameters is the key requirement. The temperature and the deformation uniformity are main parameters at the high hardness grinding balls rolling. Reduction forces can be estimated by modeling, but in this case, they were determined analytically, based on the distribution of the real specific reduction force over the observed temperature fields on the surface of the ball. Revealed a significant increase in the temperature of ball during the cross-helical rolling from equator to the poles from 880 °С to 940 °С. Established temperature increase (up to 60 °C) was observed in the area of the roll flange penetration into the workpiece, where significant deformations occur. Maximum average power of rolling generated on the top of the roll flanges has been determined, which reaches 350 MPa and decreases linearly with the distance from the top of the flange of the deformation tool and is practically reduced to zero on the equator of the ball. It was shown that linear nature of the change of the specific power of rolling is in good agreement with the linear dependence of the mill roll flange growth when it is introduced into the workpiece.

Publisher

JSC Chermetinformatsia

Reference21 articles.

1. GOST 7524–2015 Shary melyushchie stal’nye dlya sharovykh mel’nits [State Standard 7524–2015. Steel grinding balls for mall mills]. (In Russ.)

2. Rubtsov V.Yu., Shevchenko O.I. Osvoenie proizvodstva melyushchikh sharov pyatoi gruppy tverdosti v usloviyakh AO “EVRAZ-NTMK” [Mastering production of grinding balls of 5th group of hardness at JSC “EVRAZ-NTMK”]. Aktual’nye problemy sovremennoi nauki, tekhniki i obrazovaniya: tezisy dokladov 76-i Mezhdunar. nauchno-tekhnich. konf. [Actual problems of modern science, technology and education: theses of reports of the 76th Mezhdunar. scientific and technical conf.]. Magnitogorsk: izd-vo MGTU im. G.I. Nosova, 2018, vol. 1, pp. 117, 118. (In Russ.)

3. Rubtsov V.Yu., Shevchenko O.I. Mastering production of grinding balls of 5th group of hardness at JSC “EVRAZ-NTMK”. Kalibrovochnoe byuro, 2018, no. 13, pp. 20–22. (In Russ.)

4. Yur’ev A.B., Mukhatdinov I.Kh., Atkonova O.P., Kozyrev N.A., Korneva L.V. Mastering production of super high hardnessgrinding balls of 80–100 mm diameter. Stal’, 2010, no. 4, pp. 90, 91. (In Russ.)

5. Mokhov G.V. etc. Proizvodstvo melyushchikh sharov osobo vysokoi tverdosti [Production of super high hardness grinding balls]. Metallurgiya: tekhnologii, upravlenie, innovatsii, kachestvo: trudy vseros. nauchno-praktich. konf. [Metallurgy: technology, management, innovation, quality: the works of All-Russia. scientific and practical conf.]. Novokuznetsk, 2009, pp. 204–207. (In Russ.)