Study of the properties of the metal deposited with flux-cored wire of the Fe‒C‒Si‒Мn‒Сr‒W‒V system.-Reference-Cited by-同舟云学术

Study of the properties of the metal deposited with flux-cored wire of the Fe‒C‒Si‒Мn‒Сr‒W‒V system.

Published:2023-06-26 Issue:5 Volume:79 Page:391-400
ISSN:2619-0753
Container-title:Ferrous Metallurgy. Bulletin of Scientific , Technical and Economic Information
language:
Short-container-title:Černaâ metallurgiâ. Bûlletenʹ naučno-tehničeskoj informacii

Author:

Kryukov R. E.¹,Usol’tsev A. A.¹,Kozyrev N. A.²,Zhukov A. V.,¹,Kibko N. V.¹

Affiliation:

1. Siberian State Industrial University

2. FSUE “TsNIIchermet named after I. P. Bardin”

Abstract

Alloys of the Fe‒C‒Si‒Мn‒Сr‒W‒V system widely used for hot-rolling roll repairs provide high resistance of the deposited layer against abrasion, but its thermal endurance is relatively low. It is shown that in order to ensure the quality of roll repair, it is necessary to improve the composition of the flux-cored wire charge and the technology of their use. It is proposed to reduce the structural heterogeneity of the deposited metal the use of flux-cored wire of the type PP-Np-35V9X3SF. The influence of the introduction of carbon-fluorinated elements and titanium on hydrogen concentration, microstructure, level of pollution by non-metallic inclusions, grain size, hardness and rate of wear of the deposited metal layer was evaluated. The data on the chemical composition of the deposited layer, the content of non-metallic inclusions in it, the microstructure of the deposited metal, depending on the content of titanium in the flux-cored wire, are presented. It was found that an increase the concentration of titanium increases the hardness of the deposited layer and reduces the rate of wear (abrasion) of samples. The effect on the level of contamination of the studied fused layers with oxide inclusions was not revealed. Increasing the hydrogen content in the deposited layer re-duces its hardness and increases the rate of wear of the deposited layer. Increasing the content of titanium in the depos-ited layer helps to reduce the size of the martensite needles, as well as the size of the former austenite grain. The de-pendencies of HRC hardness and wear resistance on the content of titanium and hydrogen in the deposited layer were established

Publisher

South Ural State University

Subject

General Medicine

Reference22 articles.

1. Polukhin V. P., Polukhin P. I., Nikolaev V. A. Sostavnoi rabochii instrument prokatnykh stanov [Composite working tools of rolling mills]. Moscow: Metallurgiya, 1977, 88 p. (In Russ.).

2. Budag”yants N. A., Karsskii V. E. Litye prokatnye valki [Cast rolling rolls]. Moscow: Metallurgiya, 1983, 540 p. (In Russ.).

3. Polukhin V. P., Nikolaev V.A., Shul’man P. G. Nadezhnost’ i dolgovechnost’ valkov kholodnoi prokatki [Reliability and durability of cold rolling rolls]. Moscow: Metallurgiya, 1979, 503 p. (In Russ.).

4. Pavlov P. N. Osnovy inzhenernogo rascheta elementov mashin na ustalostnuyu i dlitel’nuyu prochnost’ [Basics of engineering calculation of machine elements for fatigue and long-term strength durability]. Leningrad: Mashinostroenie, 1988, 209 p. (In Russ.).

5. Khasui A. Naplavka i napylenie [Surfacing and spraying]. Moscow: Mashinostroenie, 1995, 240 p. (In Russ.).