Quintuple band circular monopole antenna with innovative 3-D printed PLA substrate for wireless applications-Reference-Cited by-同舟云学术

Quintuple band circular monopole antenna with innovative 3-D printed PLA substrate for wireless applications

Published:2021-08-06 Issue:0 Volume:0 Page:
ISSN:2191-6349
Container-title:Frequenz
language:en
Short-container-title:

Author:

Ahmed Ashraf E.¹,Ali Wael A.E.²,Das Sudipta³^ORCID

Affiliation:

1. Department of Electronics and Communication Engineering , Higher Institute of Engineering and Technology, King Marriott , Alexandria , Egypt

2. Department of Electronics and Communication Engineering , College of Engineering and Technology, Arab Academy for Science, Technology and Maritime Transport (AASTMT) , Alexandria , Egypt

3. Department of Electronics and Communication Engineering , IMPS College of Engineering and Technology , Malda , West Bengal , India

Abstract

Abstract In this paper, a circular antenna with a 3-D printed substrate is introduced to achieve a multiband behavior. The circular antenna is matched using a key-shaped stub located on the perimeter of the designed antenna. The 3-DP circular antenna adopted the apollonian gasket technique to perform the multi-circular cuttings in the Polylactic Acid (PLA) substrate as an innovative technique to obtain quintuple bands. The proposed antenna is designed to operate for Bluetooth, WLAN, WiMAX, and other wireless applications in S-band and C-band. The designed antenna has a compact size of 61.1 × 43.6 × 1 mm3. The prototype of the suggested 3-D printed antenna is fabricated and measured to confirm the simulation results. A good agreement is evident between simulation and experimental results which validates the design concept.

Publisher

Walter de Gruyter GmbH

Subject

Electrical and Electronic Engineering

Link

https://www.degruyter.com/document/doi/10.1515/freq-2021-0082/pdf

Reference39 articles.

1. E. MacDonald, R. Salas, D. Espalin, et al., “3D printing for the rapid prototyping of structural electronics,” IEEE Access, vol. 2, pp. 234–242, 2014. https://doi.org/10.1109/access.2014.2311810.

2. B. Sanz-Izquierdo and E. Parker, “3-D printing of elements in frequency selective arrays,” IEEE Trans. Antenn. Propag., vol. 62, no. 12, pp. 6060–6066, 2014, https://doi.org/10.1109/tap.2014.2359470.

3. M. Liang, C. Shemelya, E. MacDonald, R. Wicker, and H. Xin, “3-D printed microwave patch antenna via fused deposition method and ultrasonic wire mesh embedding technique,” IEEE Antenn. Wireless Propag. Lett., vol. 14, pp. 1346–1349, 2015, https://doi.org/10.1109/lawp.2015.2405054.

4. I. T. Nassar and T. M. Weller, “Development of novel 3-D cube antennas for compact wireless sensor nodes,” IEEE Trans. Antenn. Propag., vol. 60, pp. 1059–1065, 2012, https://doi.org/10.1109/tap.2011.2173121.

5. S. Jun, B. Sanz-Izquierdo, J. Heirons, et al., “Circular polarised antenna fabricated with low-cost 3D and inkjet printing equipment,” Electron. Lett., vol. 53, pp. 370–371, 2017, https://doi.org/10.1049/el.2016.4605.

Cited by 1 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. A Band Stop to Band Pass Filter Transformation Utilizing 3-D Printing Technique for C-band Applications;The Applied Computational Electromagnetics Society Journal (ACES);2023-04-25