Influence of testers on the ISE effect-Reference-Cited by-同舟云学术

Influence of testers on the ISE effect

Published:2022-04-01 Issue:4 Volume:64 Page:550-562
ISSN:0025-5300
Container-title:Materials Testing
language:en
Short-container-title:

Author:

Petrík Jozef¹,Blaško Peter¹,Domovcová Lucia²,Sedlák Richard³,Guzanová Anna⁴,Ťavodová Miroslava⁵,Pribulová Alena⁶,Futaš Peter⁶

Affiliation:

1. Institute of Materials and Quality Engineering, Faculty of Materials Metallurgy and Recycling, Technical University of Košice , Letná 9, 042 00 , Kosice , Slovakia

2. Research and Development Centre, Železiarne Podbrezová , Podbrezová , Slovakia

3. Institute of Materials Research of Slovak Academy of Sciences (SAS) , Košice , Slovakia

4. Faculty of Civil Engineering, Technical University of Košice , Kosice , Slovakia

5. Faculty Technology, Technical University of Zvolen , Studentska 26, 96001 , Zvolen , Slovakia

6. Institute of Metallurgy, Faculty of Materials Metallurgy and Recycling, Technical University of Košice , Kosice , Slovakia

Abstract

Abstract In the micro-hardness range of the load, the measurement is complicated by the occurrence of the Indentation Size Effect (ISE) – the measured value of the micro-hardness is affected by the value of the applied load. The paper aims to study the influence of the automatic testers on the character type and size of the ISE. Ten testers and five standard reference blocks were involved in the “round-robin test”. Parameters of the ISE were evaluated using Meyer’s, Hays–Kendall, and PSR methods and also by statistical methods (ANOVA, t-test, regression, and cluster analysis). Despite the assumptions, a statistically significant impact of the hardness tester was found not only on the measured value but also on the character and size of ISE.

Funder

Slovak Grant Agency for Science

Publisher

Walter de Gruyter GmbH

Subject

Mechanical Engineering,Mechanics of Materials,General Materials Science

Link

https://www.degruyter.com/document/doi/10.1515/mt-2021-2088/pdf

Reference33 articles.

1. Metallic Materials, Vickers Hardness Test. Part 1 Test Method, ISO Standard No. ISO 6507-1, Geneva, International Organization for Standardization, 2004.

2. Metallic Materials. Instrumented Indentation Test for Hardness and Materials Parameters, Part 1: Test Method, ISO Standard No. ISO 14577-1, Geneva, International Organization for Standardization, 2015.

3. G.-Z. Voyiadjis and R. Peters, “Size effects in nanoindentation: an experimental and analytical study,” Acta Mech., vol. 211, nos. 1–2, pp. 131–153, 2010, https://doi.org/10.1007/s00707-009-0222-z.

4. J. Gong, J. Wu, and Z. Guan, “Examination of the indentation size effect in low-load Vickers hardness testing of ceramics,” J. Eur. Ceram. Soc., vol. 19, no. 15, pp. 2625–2631, 1999, https://doi.org/10.1016/S0955-2219(99)00043-6.

5. K. Sangwal, B. Surowska, and P. Błaziak, “Analysis of the indentation size effect in the microhardness measurement of some cobalt-based alloys,” Mater. Chem. Phys., vol. 77, no. 2, pp. 511–520, 2003, https://doi.org/10.1016/S0254-0584(02)00086-X.

Cited by 3 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Use of Risk Management to Support Business Sustainability in the Automotive Industry;Sustainability;2024-05-20

2. The Indentation Size Effect (ISE) of Ag–Cu Alloys;Crystals;2023-01-04

3. The Indentation Size Effect (ISE) of Metals;Crystals;2022-06-02