Effect of vibratory peening on wear behavior of Al2O3/SiCp reinforced Al2024 aircraft alloy-Reference-Cited by-同舟云学术

Effect of vibratory peening on wear behavior of Al2O3/SiCp reinforced Al2024 aircraft alloy

Published:2021-10-01 Issue:10 Volume:63 Page:956-961
ISSN:2195-8572
Container-title:Materials Testing
language:en
Short-container-title:

Author:

Er Yusuf¹

Affiliation:

1. Elazig , Turkey

Abstract

Abstract Aluminum alloys and composites are widely used in the field of aviation due to their high strength/weight ratio. However, due to their relatively low hardness values, they have poor wear resistance. In this study, a hybrid composite material was produced through stir casting method. Al2O3 and SiCp particles in 2.5, 5 and 7.5 wt.-% were added into Al2024 matrix material, which is widely used in the aviation industry, in order to increase the wear resistance of composites. The vibratory peening process was applied to the surfaces of the produced samples. The samples were then subjected to a reciprocating wear test. As a result of the tests, it was observed that the vibratory peening process has an important effect on the wear resistance of the samples.

Publisher

Walter de Gruyter GmbH

Subject

Mechanical Engineering,Mechanics of Materials,General Materials Science

Link

https://www.degruyter.com/document/doi/10.1515/mt-2021-0029/pdf

Reference27 articles.

1. S. Curtis, E. R. de los Rios, C. A. Rodopoulos, A. Levers: Analysis of the effects of controlled shot peening on fatigue damage of high strength aluminium alloys, International Journal of Fatigue 25 (2003), pp. 59-66 DOI:10.1016/S0142-1123(02)00049-X

2. Y. Madhavi, L. Rama Krishna, N. Narasaiah: Influence of micro arc oxidation coating thickness and prior shot peening on the fatigue behavior of 6061-T6 Al alloy, International Journal of Fatigue 126 (2019), pp. 297-305 DOI:10.1016/j.ijfatigue.2019.05.013

3. Y. C. Lin, H. C. Li, S. S. Liou, M. T. Shie: Mechanism of plastic deformation of powder metallurgy metal matrix composites of Cu–Sn/SiC and 6061/SiC under compressive stress, Materials Science Engineering, A 373 (2004), No. 1-2, pp. 363-369 DOI:10.1016/j.msea.2004.02.011

4. K. S. K. Sasikumar, K. Dineshkumar, K. Deeban, M. Sambathkumar, N. Saravanan: Effect of shot peening on surface properties of Al7075 hybrid aluminium metal matrix composites, Materials Today: Proceedings 33 (2020), No. 7, pp. 2792-2794 DOI:10.1016/j.matpr.2020.02.676

5. M. Kok: Production and mechanical properties of Al2O3 particle-reinforced 2024 aluminium alloy composites, Journal of Materials Processing Technology 161 (2005), No. 3, pp. 381-388 DOI:10.1016/j.jmatprotec.2004.07.068

Cited by 5 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Effect of particle volume fraction on wear behavior in Al–SiC MMC coated on DIN AlZnMgCu1.5 alloy;Materials Testing;2024-02-22

2. Effects of shear deformation on grain size and mechanical properties of the forged B₄Cp/Al composite;Materials Testing;2023-09-18

3. Mechanical and tribological behaviour of novel Al–12Si-based hybrid composites;Materials Testing;2023-04-01

4. Effects of forging on the mechanical properties of B₄Cp/Al composite with flaked Al and Al₂O₃ particles;Materials Testing;2022-10-01

5. The effect of SiC content on microstructural and tribological properties of sintered B₄C and SiC reinforced Al–Cu–Mg–Si matrix hybrid composites;Materials Testing;2022-04-01