Additive manufacturing of hexagonal lattice structures: tensile tests and validation-Reference-Cited by-同舟云学术

Additive manufacturing of hexagonal lattice structures: tensile tests and validation

Published:2023-04-01 Issue:4 Volume:65 Page:505-511
ISSN:0025-5300
Container-title:Materials Testing
language:en
Short-container-title:

Author:

Ture Mustafa Okan¹²^ORCID,Evis Zafer¹³^ORCID,Ozturk Fahrettin⁴³^ORCID

Affiliation:

1. Engineering Science , Middle East Technical University , Ankara , Türkiye

2. Helicopter Executive Vice Presidency , Turkish Aerospace Industries , Inc. , Ankara , Türkiye

3. Manufacturing Executive Vice Presidency , Turkish Aerospace Industries , Inc. , Ankara , Türkiye

4. Department of Mechanical Engineering , Yildirim Beyazit Universitesi , Ankara , Türkiye

Abstract

Abstract In this paper, different hexagonal lattice structures of the tensile test specimens were designed, manufactured by additive manufacturing, and tested in three different lengths. Moreover, flat shape tensile test specimens were designed without lattice structure. Mechanical behaviors were obtained using a tensile testing machine and analyzed at a finite element program. Effect of lattice shape and infill density on mechanical behavior was investigated. Results were compared with finite element analysis to validate the simulation. Main objective of this paper is to investigate the tensile test properties of polylactic acid (PLA) test specimens with different hexagonal-shaped lattice structures and verify their finite element model. It is concluded that increasing hexagonal lattice size increases ductility up to certain degree. Elastic modulus of 15% and 100% infill density specimens was nearly same at lattice region.

Publisher

Walter de Gruyter GmbH

Subject

Mechanical Engineering,Mechanics of Materials,General Materials Science

Link

https://www.degruyter.com/document/doi/10.1515/mt-2022-0401/pdf

Reference19 articles.

1. J. Kranz, D. Herzog, and C. Emmelmann, “Design guidelines for laser additive manufacturing of lightweight structures in TiAl6V4,” J. Laser Appl., vol. 27, no. S1, p. S14001, 2015, https://doi.org/10.2351/1.4885235.

2. R. A. Vernon, “Discovering optimal unit cell configurations when designing for additive manufacturing using lattice structures,” MSc thesis, California State University, Long Beach, California, USA, 2016.

3. R. B. Kristiawan, F. Imaduddin, D. Ariawan, U. Sabino, and Z. Arifin, “A review on the fused deposition modeling (FDM) 3D printing: filament processing, materials, and printing parameters,” Open Eng., vol. 11, no. 1, pp. 639–649, 2021, https://doi.org/10.1515/eng-2021-0063.

4. R. Roj, A. Blondrath, R. Theiß, and P. Dültgen, “Quality optimization of FDM-printed (fused deposition modeling) components based on differential scanning calorimetry,” Mater. Test., vol. 64, no. 10, pp. 1544–1551, 2022, https://doi.org/10.1515/mt-2022-0199.

5. L. Qiu, J. Z. Liu, S. L. Y. Chang, Y. Wu, and D. Li, “Biomimetic superelastic graphene-based cellular monoliths,” Nat. Commun., vol. 3, no. 1, pp. 1241–1248, 2012. https://doi.org/10.1038/ncomms2251.

Cited by 4 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Experimental analysis of the effects of different production directions on the mechanical characteristics of ABS, PLA, and PETG materials produced by FDM;Materials Testing;2024-01-09

2. Structural comparison of conventional and chiral auxetic morphed aircraft rib;Materials Testing;2023-11-14

3. Effects of infill patterns and densities on crack propagation behavior in additive manufactured parts: a comparative study;Materials Testing;2023-09-13

4. Experimental investigation of mechanical properties of PLA, ABS, and PETG 3-d printing materials using fused deposition modeling technique;Materials Testing;2023-09-08