Dry-Friction Whip and Whirl Predictions for a Rotor-Stator Model With Rubbing Contact at Two Locations

Author:

Childs Dara W.1,Kumar Dhruv2

Affiliation:

1. Turbomachinery Laboratory, Texas A&M University, College Station, TX 77843

2. Graduate Research Assistant, Texas A&M University, College Station, TX 77845

Abstract

The present work investigates dry-friction whip and whirl phenomena for a rigid rotor contacting at two bearing locations. The idea originated with a paper by Clark et al. (2009, “Investigation of the NRG #40 Anemometer Slowdown,” American Wind Energy Association, Windpower 2009, Chicago, IL, pp. 1-16) on an anemometer undergoing dry-friction whip and whirl. The anemometer rotor was supported by two Teflon® bushings within an elastically supported housing. The dry-friction forces arose at the bushings. Prior models for dry friction whirl and whip have considered rub at one nonsupport location. The present analytical model consists of a rigid rotor connected to a rigid stator at two rubbing-contact locations. Analytical solutions are developed for the following normal reaction forces at the contact locations: (1) In phase, and (2) 180° out of phase. Analytical solutions are only possible for the same radius-to-clearance ratio (RCl) at the two rub locations and define regions where dry-friction whirl is possible in addition to indicating possible boundaries between whirl and whip. These solutions are similar to Black’s (1968, “Interaction of a Whirling Rotor with a Vibrating Stator Across a Clearance Annulus,” J. Mech. Eng. Sci., 10(1), pp. 1-12) and Crandall’s (1990, “From Whirl to Whip in Rotordynamics,” IFToMM Third Intl. Conf. on Rotordynamics, Lyon, France, pp. 19-26). A flexible-rotor/flexible-stator model with nonlinear connections at the bearings was developed to more correctly establish the range of possible solutions. The nonlinear connections at the rub surface are modeled using Hunt and Crossley’s 1975 contact model with Coulomb friction (Hunt and Crossley, F., 1975, “Coefficient of Restitution Interpreted as Damping in Vibroimpact,” ASME J. Appl. Mech., 42, pp. 440). Dry friction simulations are performed for the following rotor center of gravity (C.G.) configurations with respect to the contact locations: (1) Centered, (2) [3/4]-span location, and (3) overhung, outside the contacts. Predictions from the in-phase analytical solutions and the nonlinear simulations agree to some extent when the rotor mass is centered and at the [3/4]-span location due to the fact that whirl-to-whip transitions occur near the pinned rotor-stator bounce frequency. For the overhung mass case, the nonlinear simulation predicts whip at different frequencies for the two contact locations. Neither analytical solution modes predicts this outcome. No 180 deg out-of-phase solutions could be obtained via time-transient simulations. Dry-friction whirling is normally characterized as supersynchronous precession with a precession frequency equal to the running speed ω times RCl. Simulation predictions for models with different RCl ratio mimic whirling. Specifically, with increasing rotor speed, the backward precessional (BP) frequency increases at each contact location. However, individual contact velocities show slipping at all conditions. Slipping is greater at one location than the other, netting a “whirl-like” motion. For the overhung model with different RCl ratios: in addition to whipping at different frequencies the two contacts also whirl at different frequencies corresponding to the separate RCl ratios at the respective contacts. Simulations predict a different running speed for the “jump up” in precession frequency associated with a transition from whirl-to-whip with increasing running speed than for the jump-down in precession frequency for whirl-to-whip in a speed-decreasing mode.

Publisher

ASME International

Subject

Mechanical Engineering,Energy Engineering and Power Technology,Aerospace Engineering,Fuel Technology,Nuclear Energy and Engineering

Reference17 articles.

1. Shaft Rubbing;Newkirk;Mech. Eng.

2. Synchronous Whirling of a Shaft Within a Radially Flexible Annulus Having Small Radial Clearance;Black;Proc. Inst. Mech. Eng., Paper No.

3. Interaction of a Whirling Rotor with a Vibrating Stator across a Clearance Annulus;Black;J. Mech. Eng. Sci.

4. From Whirl to Whip in Rotordynamics;Crandall

5. Experimental Invesigation of Reverse Whirl of a Flexible Rotor;Lingener

Cited by 14 articles. 订阅此论文施引文献 订阅此论文施引文献,注册后可以免费订阅5篇论文的施引文献,订阅后可以查看论文全部施引文献

同舟云学术

1.学者识别学者识别

2.学术分析学术分析

3.人才评估人才评估

"同舟云学术"是以全球学者为主线,采集、加工和组织学术论文而形成的新型学术文献查询和分析系统,可以对全球学者进行文献检索和人才价值评估。用户可以通过关注某些学科领域的顶尖人物而持续追踪该领域的学科进展和研究前沿。经过近期的数据扩容,当前同舟云学术共收录了国内外主流学术期刊6万余种,收集的期刊论文及会议论文总量共计约1.5亿篇,并以每天添加12000余篇中外论文的速度递增。我们也可以为用户提供个性化、定制化的学者数据。欢迎来电咨询!咨询电话:010-8811{复制后删除}0370

www.globalauthorid.com

TOP

Copyright © 2019-2024 北京同舟云网络信息技术有限公司
京公网安备11010802033243号  京ICP备18003416号-3