SELECTION OF A METHOD FOR CONTROLLING THE GEOMETRIC DIMENSIONS OF PARTS IN GEODETIC PRODUCTION-Reference-Cited by-同舟云学术

SELECTION OF A METHOD FOR CONTROLLING THE GEOMETRIC DIMENSIONS OF PARTS IN GEODETIC PRODUCTION

Published:2023-08-28 Issue:10 Volume:8 Page:102-111
ISSN:2071-7318
Container-title:Bulletin of Belgorod State Technological University named after. V. G. Shukhov
language:en
Short-container-title:

Author:

Podolyak O.¹,Iskachev S.²,Sovkov S.²,Ovchinnikova V.³,Yarkin A.²,Lavrinov D.³

Affiliation:

1. Ural Federal University

2. Proizvodstvennoe ob'edinenie Ural'skiy optiko-mehanicheskiy zavod imeni E.S. Yalamova

3. Ural'skiy Federal'nyy universitet imeni pervogo Prezidenta Rossii B.N. El'cina

Abstract

An important aspect in the production of geodetic equipment is the control and measurement of parts of the entire unit. The problem of choosing the method for controlling the geometric dimensions of parts in the production of geodesic products is raised. Simple analysis and further choice of control method do not give a clear answer which method will best suit the requirements of a particular production unit and technological process. The researchers developed an algorithm for selecting a method for controlling the geometric dimensions of parts, consisting of 6 steps. For approbation of the proposed method of analysis control and measuring operations necessary according to technological maps in the production of electronic total stations were considered. The advantages of the algorithm presented are the consideration of the maximum number of parameters in the analysis, taking into account both technical and organizational factors. This method can be used for any object when changing the analysis parameters. The study tested the algorithm for the analysis of the most popular control methods. The first three steps of the algorithm require the formation of an expert commission, which can add subjectivity to the evaluation of the parameters of the analysis. The final steps of the control method selection algorithm are calculated. The result of the proposed method is the calculation of a weighted parametric index

Publisher

BSTU named after V.G. Shukhov

Subject

Psychiatry and Mental health,Neuropsychology and Physiological Psychology

Reference15 articles.

1. Синица М.О., Осипов Т.А., Комшин А.С. Разработка технических средств контроля геометрии изделий общего и тяжелого машиностроения // Приборы. 2022. № 11 (269). С. 14–21., Sinica M.O., Osipov T.A., Komshin A.S. Development of technical means of geometry control of products of general and heavy engineering [Razrabotka tekhnicheskih sredstv kontrolya geometrii izdelij obshchego i tyazhelogo mashinostroeniya]. Pribory. 2022. No. 11 (269). Pp. 14–21. (rus)

2. Лексутов И.С., Клюка В.П. К возможности применения линейного сканера для создания средств технического контроля геометрических параметров продольного сечения поверхности катания колеса вагона // Известия Транссиба. 2022. № 3 (51). С. 51–63., Leksutov I.S., Klyuka V.P. To the possibility of using a linear scanner to create means of technical control of geometric parameters of the longitudinal section of the rolling surface of the railcar wheel [K vozmozhnosti primeneniya linejnogo skanera dlya sozdaniya sredstv tekhnicheskogo kontrolya geometricheskih parametrov prodol'nogo secheniya poverhnosti kataniya kolesa vagona]. Journal of Transsib railway studies. 2022. No. 3 (51). Pp. 51-63. (rus)

3. Голубева О.А., Мирный В.И., Фоменко О.Н. Анализ применения координатно-измерительных машин при производстве сельскохозяйственной техники // Прогрессивные технологии и процессы : сборник научных статей 6-й Всероссийской научно-технической конференции с международным участием. Курск: Юго-Западный государственный университет, 2019. С. 50-53., Golubeva O.A., Mirny V.I., Fomenko O.N. Analysis of the application of coordinate measuring machines in the manufacture of agricultural machinery [Analiz primeneniya koordinatno-izmeritel'nyh mashin pri proizvodstve sel'skohozyajstvennoj tekhniki]. Progressivnye tekhnologii i processy : sbornik nauchnyh statej 6-j Vserossijskoj nauchno-tekhnicheskoj konferencii s mezhdunarodnym uchastiem. Kursk: YUgo-Zapadnyj gosudarstvennyj universitet. 2019. Pp. 50-53. (rus)

4. Чепчуров М.С., Сумской А.М., Жигулина Ю.А., Подпрятов Д.В. Идентификация искажения формы цилиндрических деталей технологических агрегатов // Автоматизация и моделирование в проектировании и управлении. 2022. № 4 (18). С. 29–36. DOI: 10.30987/2658-6436-2022-4-29-36, Chepchurov M.S., Sumskoi A.M., Jigulina Yu.A., Podpriatov D.V. Distortion identification of the cylindrical part form of technological units [Identifikaciya iskazheniya formy cilindricheskih detalej tekhnologicheskih agregatov]. Automation and modeling in design and management. 2022. No. 4 (18). Pp. 29-36. (rus) DOI: 10.30987/2658-6436-2022-4-29-36

5. Кузнецова Е.Ю., Подоляк О.О., Минина Е.В. Ценообразование промышленной продукции при выведении на рынок // На страже экономики. 2022. № 4 (23). С. 79–92. DOI: 10.36511/2588-0071-2022-4-79-92., Kuznetsova E.Yu., Podoliak O.O. Minina E.V. Pricing of industrial products when entering the market [Cenoobrazovanie promyshlennoj produkcii pri vyvedenii na rynok]. The economy under guard. 2022. No. 4 (23). Pp. 79-92. (rus) DOI: 10.36511/2588-0071-2022-4-79-92