IBER CONCRETE FOR 3D-PRINTING-Reference-Cited by-同舟云学术

IBER CONCRETE FOR 3D-PRINTING

Published:2019-04-10 Issue:3 Volume:4 Page:22-27
ISSN:2071-7318
Container-title:Bulletin of Belgorod State Technological University named after. V. G. Shukhov
language:en
Short-container-title:

Author:

Шорстова Елена¹,Shorstova Elena²,Клюев Сергей¹,Klyuev Sergey²,Клюев Александр³,Klyuev Aleksandr²

Affiliation:

1. Белгородский государственный технологический университет им В.Г. Шухова

2. Belgorod State Technological University named after V.G. Shukhov

3. Белгородский государственный технологический университет им. В.Г. Шухова

Abstract

The article deals with the possibility of using 3D-printing in the construction industry. The analysis of the work performed in this area in the world. It also presents the main advantages of this method of construction of structures and buildings in general. Experimental studies were carried out using the components of the mixture: CEM I 42.5H Sebryakovcement, fine ground quartzitic sandstone with a specific surface of 700 m2/ kg using gypsum. Sand was used as fine aggregate. To make the mixture plasticity, such additives as plasticizer PFM-NLK and Murapor Kombi 756 were used. Basalt fiber was used as a reinforcing agent. Were developed compositions of the concrete mixture dispersed reinforced with basalt fiber. The work was able to develop the composition of fiber-reinforced concrete mixture, which can be used for 3D- printing. Its strength characteristics were determined, allowing to conclude that this composition meets all the requirements for this technology.

Publisher

BSTU named after V.G. Shukhov

Subject

Psychiatry and Mental health,Neuropsychology and Physiological Psychology

Reference16 articles.

1. ASTM Standard, Standard Terminology for Additive Manufacturing Technologies, vol. 10.04., ASTM Standard, Standard Terminology for Additive Manufacturing Technologies, vol. 10.04.

2. Additive Manufacturing Study Shows Cuts in Material Consumption and Reduced CO2 Emissions, Powder Metall Rev., (2013) http://www.ipmd.net/articles/002490.html., Additive Manufacturing Study Shows Cuts in Material Consumption and Reduced CO2 Emissions, Powder Metall Rev., (2013) http://www.ipmd.net/articles/002490.html.

3. Holmstrom J., Partanen J., Tuomi H., Walter M. Rapid Manufacturing in the Spare Parts Supply Chain: Alternative Approaches to Capacity Deployment. Journal of Manufacturing Technology Management, 2010, 21, pp. 687–697, Holmstrom J., Partanen J., Tuomi H., Walter M. Rapid Manufacturing in the Spare Parts Supply Chain: Alternative Approaches to Capacity Deployment. Journal of Manufacturing Technology Management, 2010, 21, pp. 687–697.

4. Bourell D.L., Beaman J.L., Leu M.C., Rosen D.W. A Brief History of Additive Manufacturing and the 2009 Roadmap for Additive Manufacturing: Looking Back and Looking Ahead, U.S. Turkey Workshop on Rapid Technologies, (2009)., Bourell D.L., Beaman J.L., Leu M.C., Rosen D.W.A Brief History of Additive Manufacturing and the 2009 Roadmap for Additive Manufacturing: Looking Back and Looking Ahead, U.S. Turkey Workshop on Rapid Technologies, (2009).

5. Additive Manufacturing: Opportunities and Constraints, A report of Roundtable Hosted by the Royal Academy of Engineering, (2013), http://www.raeng.org.uk/publications/reports/additive-manufacturing., Additive Manufacturing: Opportunities and Constraints, A report of Roundtable Hosted by the Royal Academy of Engineering, (2013), http://www.raeng.org.uk/publications/reports/additive-manufacturing.

Cited by 3 articles. 订阅此论文施引文献订阅此论文施引文献，注册后可以免费订阅5篇论文的施引文献，订阅后可以查看论文全部施引文献

1. Modified Gypsum-Cement-Pozzolan Concrete for 3DCP;Construction Materials;2024-09-12

2. INFORMATION MODELING AND ADDITIVE TECHNOLOGIES IN CONSTRUCTION;Construction and Architecture;2021-10-29

3. FOR THE STUDY OF PECULIARITIES OF STRUCTURE FORMATION OF COMPOSITE BINDERS FOR NON-AUTOCLAVED AERATED CONCRETE;Construction Materials and Products;2020-06-04