Tensile, bending, and impact properties of laminated carbon/aramid/glass hybrid fiber composites-Reference-Cited by-同舟云学术

Tensile, bending, and impact properties of laminated carbon/aramid/glass hybrid fiber composites

Published:2023-09-08 Issue:12 Volume:65 Page:1826-1835
ISSN:0025-5300
Container-title:Materials Testing
language:en
Short-container-title:

Author:

Ekşi Seçil¹^ORCID,Danyildiz Fatih Emir¹²,Özsoy Neslihan¹³^ORCID,Özsoy Murat¹⁴^ORCID

Affiliation:

1. Sakarya Universitesi , Sakarya , 54050 , Türkiye

2. Sakarya Universitesi , Sakarya , Türkiye

3. Mechanical Engineering , Sakarya Universitesi , Sakarya , 54050 , Türkiye

4. Mechanical Engineering , Sakarya University , Sakarya Üniversitesi Mühendislik Fakültesi Makine Mühendisliği Bölümü , Serdivan , Sakarya , 54050 , Türkiye

Abstract

Abstract In this study, hybrid (carbon, glass, and aramid) fabric epoxy composite laminates were fabricated with different layering sequences by hand lay-up. The effects of layering arrangements of laminated composite fibers on the mechanical properties of hybrid composites were investigated. Tensile, bending, and impact tests were performed to obtain the mechanical behaviors of hybrid composites. It was found that the layering sequences significantly affect the tensile, bending strength, and impact energy. As a result of the tensile tests, the highest tensile strength was obtained in the 3C + 3G combination. The highest load-carrying capacity in three-point bending tests was obtained in the 2G + 2A + 2C combination. The combination with the highest impact energy was 2C + 2G + 2A, and the lowest was 3C + 3G. It has been observed that hybrid composites containing aramid fiber absorb higher impact energy than others. The results showed that the layering sequences are essential in hybrid composites with the same fiber and layer number.

Publisher

Walter de Gruyter GmbH

Subject

Mechanical Engineering,Mechanics of Materials,General Materials Science

Link

https://www.degruyter.com/document/doi/10.1515/mt-2023-0207/pdf

Reference38 articles.

1. M. A. Attia, M. A. A. El-baky, M. M. Abdelhaleem, and M. A. Hassan, “Hybrid composite laminates reinforced with flax-basalt-glass woven fabrics for lightweight load bearing structures,” J. Ind. Textil., vol. 51, no. 3, pp. 4622S–4664S, 2022, https://doi.org/10.1177/1528083720960743.

2. J. W. Bao, Y. W. Wang, R. An, H. W. Cheng, and F. C. Wang, “Investigation of the mechanical and ballistic properties of hybrid carbon/aramid woven laminates,” Defence Technol., vol. 18, no. 10, pp. 1822–1833, 2022, https://doi.org/10.1016/j.dt.2021.09.009.

3. Ö. F. Erkendirci, A. Avcı, L. Dahil, K. Kaya, S. Kılıçtek, and A. Sezgin, “Experimental investigation of tensile and impact response of nano-alumina-filled epoxy hybrid composites reinforced with carbon-kevlar and carbon-glass fabrics,” Arab J. Sci. Eng., vol. 47, no. 12, pp. 16135–16148, 2022, https://doi.org/10.1007/s13369-022-06848-9.

4. A.-S. A. K. Jassim, K. Ramazan, K. Halis, and O. Ozdemir, “Experimental investigation of the impact behavior of glass/epoxy composite materials with the natural fiber layer,” Mater. Test., vol. 64, no. 6, pp. 780–786, 2022, https://doi.org/10.1515/mt-2021-2133.

5. M. E. Deniz, R. Bardakci, and F. Aydın, “Buckling in rectangular hybrid composite plates with angled groove-shaped cut-outs,” Mater. Test., vol. 65, no. 3, pp. 332–345, 2023, https://doi.org/10.1515/mt-2022-0317.